LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 215 (Seat) >> FRONT SEAT ASSEMBLY (for Hatchback) >> Reassembly

FRONT SEAT ASSEMBLY (for Hatchback): Reassembly

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:

The procedure described below is for the driver side. Use the same procedure for both the front passenger and driver sides, unless otherwise specified.

Fig 1: Identifying Occupant Classification ECU Claw
G04834290Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. INSTALL SEAT POSITION SENSOR (for Driver Side) 
    1. Provisionally install the seat position sensor.
      NOTE:
      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position sensor with a new one.
      • When installing the seat position sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.
    2. Install a 1 mm (0.04 in.) feeler gauge between the seat rail and seat position sensor, as shown in Fig 2 .

      HINT:

      Make sure that the clearance between the seat position sensor and seat rail is within 0.6 to 2 mm (0.023 to 0.079 in.).

    3. Push the top of the seat position sensor toward the seat rail.
    4. While holding the seat position sensor, tighten the seat position sensor using "Torx" socket wrench T30.

      Torque: 8.0 N*m (70 kgf*cm, 71 in.*lbf) 

      Fig 2: Identifying Seat Position Sensor Bolt
      G04834291Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Engage the pin and install a new seat position sensor protector.
      NOTE: Do not damage portion A when installing the seat position sensor protector.
      Fig 3: Identifying Seat Position Sensor Protector Pin
      G04834292Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) 
    1. Engage the claw and install the occupant classification ECU.
      Fig 4: Identifying Occupant Classification ECU Claw
      G04834290Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL FRONT SEAT WIRE (for Front Passenger Side) 
    1. Install the front seat wire with the 2 clamps.
    2. Connect the 5 connectors.
      Fig 5: Identifying Front Seat Wire Clamps
      G04834289Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH 
    1. Engage the 2 claws and install the front seat cushion lower shield.
      Fig 6: Locating Front Seat Cushion Lower Shield Claws
      G04834285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH 
    1. Engage the claw and install the front seat cushion lower shield.
    2. Tighten the screw.
      Fig 7: Locating Front Seat Cushion Lower Shield Claw
      G04834286Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH 
    1. Install the reclining adjuster outside cover with the screw.
  7. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH 

    HINT:

    Use the same procedure as for the LH side.

    Fig 8: Locating Reclining Adjuster Outside Cover Screw
    G04834284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL RECLINING ADJUSTER INSIDE COVER LH 
    1. Engage the claw and install the reclining adjuster inside cover.
    2. Tighten the screw.
  9. INSTALL RECLINING ADJUSTER INSIDE COVER RH 

    HINT:

    Use the same procedure as for the LH side.

    Fig 9: Locating Reclining Adjuster Inside Cover Claw
    G04834283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) 
    1. Install the front seat side airbag with the 2 nuts.

      Torque: 5.5 N*m (55 kgf*cm, 49 in.*lbf) 

      Fig 10: Locating Front Seat Side Airbag With Nuts
      G04834299Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 2 clamps.
      Fig 11: Locating Clamps
      G04834281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the 3 clamps and the airbag connector.
      Fig 12: Locating Airbag Connector & Clamps
      G04834280Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSTALL FRONT SEATBACK COVER PAD 
    1. Install the front seatback cover pad.
      NOTE: The fabring for fixing the airbag must mot be wrinkled when installing the front seatback cover pad (w/ Front Seat Side Airbag).
      Fig 13: Identifying Front Seatback Cover Pad
      G04834302Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using hog ring pliers, install 3 new hog rings.
      Fig 14: Installing New Hog Rings
      G04834303Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. INSTALL FRONT SEAT HEADREST SUPPORT 

    HINT:

    Use the same procedure for both sides.

    1. Align the protruding portion of the front seat headrest support with the installation groove of the front seat back frame.
    2. Engage the 2 claws and install the front seat headrest support.
      Fig 15: Identifying Front Seat Headrest Support Claws
      G04834304Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL (for Walk in Seat Type) 
    1. Engage the 5 claws and install the reclining remote control lever bezel.
      Fig 16: Identifying Reclining Remote Control Lever Bezel Claws
      G04834278Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL RECLINING REMOTE CONTROL LEVER (for Walk in Seat Type) 
    1. Engage the claw and install the reclining adjuster release handle.
      Fig 17: Identifying Reclining Adjuster Release Handle Claw
      G04834306Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL FRONT SEAT CUSHION COVER PAD 
    1. Engage the 2 claws and 9 hooks, and install the front seat cushion cover pad.
      Fig 18: Identifying Front Seat Cushion Cover Pad Claws & Hooks
      G04834274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/ Front Seat Side Airbag:
      1. Fix the front seat side airbag wire harness with the front seat cushion cover pad fixing cover.
    3. for Clip Type:
      1. Install the 2 clips.
    4. for J Hook Type:
      1. Engage the 2 hooks.
        Fig 19: Identifying Hooks & Clip
        G04834273Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Install the front seatback cover band.
      Fig 20: Identifying Front Seatback Cover Band
      G04834272Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. INSTALL FRONT SEAT CUSHION SHIELD RH 
    1. Engage the claw and the clip and install the front seat cushion shield.
    2. Tighten the screw.
  17. INSTALL FRONT SEAT INNER BELT ASSEMBLY (See  INSTALLATION  ) 
    Fig 21: Locating Front Seat Cushion Shield Screw (RH)
    G04834271Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. INSTALL FRONT SEAT CUSHION SHIELD LH 
    1. Engage the 2 claws and the clip and install the front seat cushion shield.
    2. Tighten the screw.
      Fig 22: Locating Front Seat Cushion Shield Screw (LH)
      G04834270Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. INSTALL RECLINING ADJUSTER RELEASE HANDLE 
    1. Engage the claw and install the reclining adjuster release handle.
scientia non olet · About LEMON Manuals