LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 194 (Supplemental Restraint System) >> REAR AIRBAG SENSOR (for 5 Door) >> Installation

REAR AIRBAG SENSOR (for 5 Door): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
NOTE: Always use "Torx" socket wrench E10 when installing the rear seat.

HINT:

The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.

  1. INSTALL REAR AIRBAG SENSOR 
    1. Confirm that the ignition switch is turned to OFF.
    2. Confirm that the negative battery terminal is detached.
      CAUTION:
      • Confirm that the negative battery terminal is disconnected before performing the operation. Even an impact to only the airbag sensor will cause the airbag to deploy.
    3. Insert the hook into the body hole and install the airbag sensor with the bolt.

      Torque: 9.0 N*m (90 kgf*cm, 80 in.*lbf) 

      NOTE:
      • Do not use a rear airbag sensor that has been dropped.
      • Do not subject the rear airbag sensor to any impact or force.
    4. Confirm that there is no looseness by shaking the rear airbag sensor.
      Fig 1: Identifying Airbag Sensor Bolt
      G04830482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Connect the airbag connector.
      Fig 2: Detaching Airbag Connector
      G04830481Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. Engage the 3 clips and the 6 claws and install the deck trim side panel.
    2. Tighten the 3 screws.

      HINT:

      When installing the rear seat outer belt assembly RH, connect the room light connector and install the deck trim side panel assembly RH.

      3. Fig 3: Locating Deck Trim Side Panel
      G04830489Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH  (See INSTALLATION )
  4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Install the rear door opening trim weatherstrip.
  5. INSTALL REAR DOOR SCUFF PLATE RH  (See INSTALLATION )
  6. INSTALL REAR DECK TRIM COVER  (See INSTALLATION )
  7. INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)  (See INSTALLATION )
    Fig 4: Identifying Rear Opening Trim Weatherstrip
    G04830488Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)  INSTALLATION 
  9. INSTALL NO. 2 REAR SEAT LEG COVER (for 60/40 Split Seat Type)  (See INSTALLATION )
  10. INSTALL NO. 1 REAR SEAT LEG COVER (for 60/40 Split Seat Type)  (See INSTALLATION )
  11. INSTALL REAR SEATBACK ASSEMBLY (for Hold Down Seat Type)  INSTALLATION 
  12. INSTALL REAR SEAT CUSHION COVER PAD SUB-ASSEMBLY (for Hold Down Seat Type)  INSTALLATION 
  13. INSTALL DECK FLOOR BOX RH  (See INSTALLATION )
  14. INSTALL DECK FLOOR BOX LH  (See INSTALLATION )
  15. INSTALL DECK BOARD SUB-ASSEMBLY  (See INSTALLATION )
  16. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY  (See INSTALLATION )
  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  18. INSPECT SRS WARNING LIGHT 

    (See DIAGNOSIS SYSTEM  )

scientia non olet · About LEMON Manuals