LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> Camry Base, Automatic >> Repair and Diagnosis >> Suspension >> Wheels & Tire System >> Tire & Wheel (Except Hybrid) >> Tire Pressure Warning System >> DTC C2171/71 Transmitter ID not Registered >> Inspection Procedure

Inspection Procedure

NOTE:
  • When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using Techstream and write them down before removal.
  • It is necessary to perform initialization (See INITIALIZATION  ) after registration (See REGISTRATION  ) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.
  1. CONFIRM REGISTRATION CONDITION (REGISTERED ID CODES) 
    1. Turn the ignition switch off.
    2. Connect Techstream to the DLC3.
    3. Turn the ignition switch on (IG) and turn the tester on.
    4. Enter the following menus:
      1. Select: Chassis / Tire Pressure Monitor / Data List
    5. Check the values by referring to the table below.

      Tire Pressure Monitor 

      TIRE PRESSURE MONITOR DATA LIST

      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Registered ID1 Code Registered ID1 code/ min.: 0 max.: FFFFFFF* The ID No. registered in the transmitter ID1 is displayed *: Displayed only when the ID No. is not registered.
      Registered ID2 Code Registered ID2 code/ min.: 0 max.: FFFFFFF* The ID No. registered in the transmitter ID2 is displayed *: Displayed only when the ID No. is not registered.
      Registered ID3 Code Registered ID3 code/ min.: 0 max.: FFFFFFF* The ID No. registered in the transmitter ID3 is displayed *: Displayed only when the ID No. is not registered.
      Registered ID4 Code Registered ID4 code/ min.: 0 max.: FFFFFFF* The ID No. registered in the transmitter ID4 is displayed *: Displayed only when the ID No. is not registered.
      Registered ID5 Code Registered ID5 code/ min.: 0 max.: FFFFFFF* The ID No. registered in the transmitter ID5 is displayed *: Displayed only when the ID No. is not registered.

      OK: 

      The registered transmitter ID codes are displayed on the tester screen. 

    NG: Go to step 2 

    OK: REPLACE TIRE PRESSURE WARNING ECU (See  REMOVAL   ) 

  2. PERFORM REGISTRATION (TRANSMITTER ID) 
    1. Register the transmitter IDs for all the wheels (See REGISTRATION  ).
  3. CONFIRM TIRE INFLATION PRESSURE (DATA LIST) 
    1. Turn the ignition switch off.
    2. Connect Techstream to the DLC3.
    3. Turn the ignition switch on (IG) and turn the tester on.
    4. Enter the following menus:
      1. Select: Chassis / Tire Pressure Monitor / Data List
    5. Check the values by referring to the table below.

      Tire Pressure Monitor 

      TIRE PRESSURE MONITOR DATA LIST

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ID1 Tire Inflation Pressure ID1 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/ cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID2 Tire Inflation Pressure ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/ cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID3 Tire Inflation Pressure ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa(-1 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/ cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID4 Tire Inflation Pressure ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa(-1 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/ cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID5 Tire Inflation Pressure ID5 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure/-100 kPa(-1 kgf/cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 . 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/ cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      HINT:
      • *: It may take about 2 or 3 minutes until the values are displayed.
      • If no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.

      Result 

      RESULT CHART

      Result Proceed to
      All tire pressure readings are equal to specified values. A
      Tire pressure values are not displayed. B

    B : REPLACE TIRE PRESSURE WARNING ECU (See  REMOVAL   ) 

    A : END 

scientia non olet · About LEMON Manuals