REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for RH Side): Disassembly

1. Remove the 2 screws and 2 tonneau cover hook holders.

1. Using a molding remover, disengage the 8 claws and remove the 2 rear seatback covers.
   Fig 1: Identifying Claws Of Rear Seatback Cover

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disengage the 6 clips and remove the rear seatback board carpet assembly.
   Fig 2: Identifying Clips Of Rear Seatback Board Carpet Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a clip remover, remove the clip.
2. Remove the screw.
3. Remove the reclining cover protector LH as shown in the illustration.
   Fig 3: Locating Reclining Cover Protector LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the screw.
2. Disengage the claw and remove the center seat hinge cover upper LH as shown in the illustration.
Fig 4: Locating Center Seat Hinge Cover Upper LH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the screw.
2. Using a "Torx" socket wrench (T45), remove the "Torx" bolt.
3. Remove the 3 bolts and center seatback assembly.

1. Using a clip remover, remove the clip.
2. Remove the screw and reclining cover protector RH.

1. Using a "Torx" socket wrench (T45), remove the "Torx" bolts and rear seatback hinge sub-assembly center.
2. Remove the 3 screws and rear seatback molding LH.

1. Using a "Torx" socket wrench (T45), remove the "Torx" bolts and rear seatback hinge sub-assembly center.
2. Remove the 3 screws and rear seatback molding RH.

1. Using a "Torx" socket wrench (T45), remove the 2 "Torx" bolts.
2. Remove the nut, rear seat center armrest support and rear seat armrest assembly center.

1. Disengage the 2 claws and remove the rear seat headrest support (LH side).
Fig 5: Locating Hog Rings
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Remove the 2 screws.
2. Using a molding remover, disengage the 2 claws and remove the No.1 seatback cover.

1. Remove the 2 screws and No.2 center seatback cover.

1. Remove the 2 screws.
2. Disconnect the claw and remove the rear seat cushion molding RH as shown in the illustration.
   Fig 6: Locating Claw And Rear Seat Cushion Molding RH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 2 screws.
2. Disengage the 3 claws and remove the rear seat cushion molding rear RH.
   Fig 7: Identifying Screws And Claws Of Rear Seat Cushion Molding Rear RH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a "Torx" socket wrench (T45), remove the 2 "tone" bolts.
2. Remove the hog rings.
3. Remove the 2 bolts and separate type rear seat cushion assembly.

1. Disengage the hooks and remove the hog rings and rear seat cushion frame sub-assembly.

1. Remove the hog rings and separate type rear seat cushion cover.

1. Using a screwdriver, disengage the 2 claws and remove the rear seatback lock striker cover.

   HINT:

   Tape the screwdriver tip before use.

1. Remove the 2 screws.
Fig 8: Identifying Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the rear seat reclining control cable and remove the rear seat lock control lever sub-assembly.

1. Disengage the 2 claws and remove the rear seat headrest support (LH side).
   Fig 9: Locating Hog Rings

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Using a screwdriver, disengage the 4 claws and remove the rear seatback lock bezel upper.
   Fig 10: Locating Claws And Rear Seatback Lock Bezel Upper

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT:

   Tape the screwdriver tip before use.

1. Remove the bolt and disconnect the floor anchor side of the rear center seat outer belt assembly.
   Fig 11: Identifying Bolt

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the 2 clips.
3. Remove the bolt and rear seat belt hook.
4. Disengage the hooks and remove the hog rings and separate type rear seatback cover with pad.

1. Remove the hog rings and separate type rear seatback cover.

1. Disengage the 2 claws and remove the rear seat shoulder belt cover as shown in the illustration.
Fig 12: Locating Claw Of Rear Seat Shoulder Belt Cover
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the bolt and fold seat stopper band assembly No. 1.

1. Remove the screw.
2. Disengage the claw and remove the rear seat reclining cover inner RH.

1. Remove the screw and rear seat cover No.1.

1. Remove the screw and rear seat cover No.2.

1. Disconnect the 2 cables and remove the rear seat reclining control cable.

1. Using a "Torx" socket wrench (T45), remove the 2 "Torx" bolts.
2. Remove the 2 bolts and rear seatback frame sub-assembly.

1. Remove the clamp.
2. Disconnect the 2 seat track stop plate cables.
3. Remove the 2 nuts and seat track stop plate.

1. Remove the 2 E-rings and 2 springs.
2. Remove the bolt, nut and reclining control link sub-assembly.

1. Using a "Torx" socket wrench (T45), remove the 3 "Torx" bolts.
2. Using a "Torx" socket wrench (T55), remove the 2 "Torx" bolts and rear seatback frame sub-assembly lower.

1. Remove the 4 nuts and 2 fold seat cushion frames No.2.

1. Move the rear seat track assembly outer and rear seat track assembly inner fully forward by operating the rear seat track adjusting handle.
2. Using a hexagon wrench 1.5 mm (0.059 in.), push down the 2 handle stoppers as shown in the illustration and remove the rear seat track adjusting handle.
Fig 13: Locating Rear Seat Track Adjusting Handle
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002