LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2007 >> Highlander Hybrid Limited, AWD >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat (Hybrid) >> REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for LH Side) >> Reassembly

REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for LH Side): Reassembly

  1. INSTALL REAR SEAT TRACK ASSEMBLY INNER LH 
  2. INSTALL REAR SEAT TRACK ASSEMBLY OUTER LH 
  3. INSTALL REAR SEAT TRACK ADJUSTING HANDLE 
  4. INSTALL FOLD SEAT CUSHION FRAME NO.1 
    1. Install the 2 fold seat cushion frames No. 1 with the 4 nuts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  5. INSTALL REAR SEAT BACK FRAME SUB-ASSEMBLY LOWER 
    1. Using a "Torx" socket wrench (T45), install the rear seatback frame sub-assembly lower with the 5 "Torx" bolts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  6. INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY 
    1. Install the reclining control link sub-assembly with the 4 nuts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

    2. Install the spring and a new E-ring.
  7. INSTALL SEAT TRACK STOP PLATE 
    1. Install the seat track stop plate with the 2 nuts.

      Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

    2. Install the 2 seat track stop plate cables.
    3. Install the clamp.
  8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY 
    1. Using a "Torx" socket wrench (T45), install the rear seatback frame sub-assembly with the 4 "Torx" bolts.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

  9. INSTALL REAR SEAT RECLINING CONTROL NO.2 CABLE 
  10. INSTALL REAR SEAT COVER NO.2 
  11. INSTALL REAR SEAT RECLINING COVER INNER LH 
  12. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY NO.2 
  13. INSTALL SEPARATE TYPE REAR SEATBACK PAD 
  14. INSTALL SEPARATE TYPE REAR SEATBACK COVER 
    1. Using hog ring pliers, install the separate type rear seatback cover to the rear seatback pad with new hog rings.
      Fig 1: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
      G05244023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  15. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD 
  16. INSTALL REAR SEAT HEADREST SUPPORT 
  17. INSTALL REAR SEAT HEADREST SUPPORT 
  18. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY 
  19. INSTALL REAR SEATBACK LOCK STRIKER COVER 
  20. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY 
  21. INSTALL REAR SEATBACK COVER 
  22. INSTALL TONNEAU COVER HOOK HOLDER 
  23. INSTALL REAR SEAT HEADREST ASSEMBLY 
  24. INSTALL REAR SEAT BELT ASSEMBLY INNER  (See INSTALLATION )
  25. INSTALL REAR SEAT CUSHION PAD 
  26. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER 
    1. Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with new hog rings.
      Fig 2: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
      G05244023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  27. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY 
  28. INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY 
    1. Install the 2 bolts.

      Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

    2. Install the 2 rubber bands on the backside of the rear seatback board carpet assembly.
    3. Using a "Torx" socket wrench (T45), install the separate type rear seat cushion assembly with the 2 "Torx" bolts.

      Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf) 

  29. INSTALL REAR SEAT CUSHION MOLDING REAR LH 
  30. INSTALL REAR SEAT CUSHION MOLDING LH 
scientia non olet · About LEMON Manuals