REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 2 Seat for RH Side): Reassembly

INSTALL REAR SEAT TRACK ASSEMBLY INNER
INSTALL REAR SEAT TRACK ASSEMBLY OUTER
INSTALL REAR SEAT TRACK ADJUSTING HANDLE
INSTALL FOLD SEAT CUSHION FRAME NO.2
1. Install the 2 fold seat cushion frames No.2 with the 4 nuts.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LOWER
1. Using a "Torx" socket wrench (T45), install the rear seatback frame sub-assembly lower with the 5 "Torx" bolts.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL RECLINING CONTROL LINK SUB-ASSEMBLY
1. Install the reclining control link sub-assembly with the 4 nuts.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
2. Install the 2 springs and 2 new E-rings.
INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY
1. Install the rear back lock control lever sub-assembly with the 3 nuts.
  Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
INSTALL SEAT TRACK STOP PLATE
1. Install the seat track stop plate with the 2 nuts.
  Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
2. Install the 2 seat track stop plate cables.
3. Install the clamp.
INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
1. Using a "Torx" socket wrench (T45), install the rear seatback frame sub-assembly with the 4 "Torx" bolts.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL REAR SEAT RECLINING CONTROL NO.2 CABLE
INSTALL REAR SEAT COVER NO.2
INSTALL REAR SEAT RECLINING COVER INNER RH
INSTALL SEAT TRACK UPPER RAIL COVER RH
INSTALL REAR SEATBACK COVER NO.2 RH
INSTALL RECLINING ADJUSTER INSIDE COVER RH
INSTALL SEPARATE TYPE REAR SEATBACK PAD
INSTALL SEPARATE TYPE REAR SEATBACK COVER
1. Using hog ring pliers, install the separate type rear seatback cover to the rear seatback pad with new hog rings.
  
  Fig 1: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  NOTE:
  - Be careful not to damage the cover.
  - When installing the hog rings, take care to minimize wrinkles as much as possible.
INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD
INSTALL REAR SEAT HEADREST SUPPORT
INSTALL REAR SEAT HEADREST SUPPORT
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
INSTALL REAR SEATBACK LOCK STRIKER COVER
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY
INSTALL REAR SEATBACK COVER
INSTALL TONNEAU COVER HOOK HOLDER
INSTALL REAR SEAT COVER BEZEL NO.1
INSTALL REMOTE CONTROL LEVER KNOB
INSTALL REAR SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT BELT ASSEMBLY INNER (See INSTALLATION )
INSTALL REAR SEAT CUSHION PAD
INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
1. Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad with new hog rings.
  
  Fig 2: Installing Separate Type Rear Seat Cushion Cover To Rear Seat Cushion Pad With New Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  NOTE:
  - Be careful not to damage the cover.
  - When installing the hog rings, take care to minimize wrinkles as much as possible.
INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY
INSTALL SEPARATE TYPE REAR SEAT CUSHION ASSEMBLY
1. Install the 2 bolts.
  Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
2. Install new 2 clamps.
3. Install the 2 rubber bands on the backside of the rear seatback board carpet assembly.
4. Using a "Torx" socket wrench (T45), install the separate type rear seat cushion assembly with the 2 "Torx" bolts.
  Torque: 21 N*m (214 kgf*cm, 16 ft.*lbf)
INSTALL RECLINING HINGE COVER RH
INSTALL VERTICAL ADJUSTER BRACKET COVER OUTER
INSTALL REAR SEAT CUSHION MOLDING REAR RH
INSTALL REAR SEAT CUSHION MOLDING RH