DTC P0E51-28: Dc/Dc Converter Current Sensor Signal Bias Level Out Of Range/Zero Adjustment Failure: Notes

WARNING: This page is about a different variant/trim than selected.

1. -

Detecting condition:

Reactor current sensor offset malfunction

When the reactor current sensor output deviates from the specified range in the area where current does not originally flow

(1 trip detection logic)

Trouble symptom:

Reduced output power

CAUTION: Before performing diagnosis, refer to "CAUTION" in "General Description". Ref. to P-HEV DRIVE MOTOR (DIAGNOSTICS)>GENERAL DESCRIPTION>CAUTION .

Courtesy of SUBARU OF AMERICA, INC.

CHECK DTC .

Read the following DTCs using Subaru Select Monitor. Ref. to P-HEV HYBRID POWERTRAIN CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Ref. to P-HEV DRIVE MOTOR (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .

P-HEV Hybrid Powertrain Control
P-HEV Drive Motor

NOTE:

Malfunction contents	System	Related DTC
Insulation malfunction	P-HEV Hybrid Powertrain Control	P1C7C49	HYBRID/EV BATTERY VOLTAGE SYSTEM ISOLATION (A/C AREA) INTERNAL ELECTRONIC FAILURE
		P1C7D49	HYBRID/EV BATTERY VOLTAGE SYSTEM ISOLATION (HYBRID/EV BATTERY AREA) INTERNAL ELECTRONIC FAILURE
		P1C7E49	HYBRID/EV BATTERY VOLTAGE SYSTEM ISOLATION (TRANSAXLE AREA) INTERNAL ELECTRONIC FAILURE
		P1C7F49	HYBRID/EV BATTERY VOLTAGE SYSTEM ISOLATION (DIRECT CURRENT AREA) INTERNAL ELECTRONIC FAILURE
Microcomputer malfunction	P-HEV Drive Motor	P0A1A47	GENERATOR CONTROL MODULE WATCHDOG/SAFETY MC FAILURE
		P0A1A49	GENERATOR CONTROL MODULE INTERNAL ELECTRONIC FAILURE
		P0A1B1F	GENERATOR CONTROL MODULE CIRCUIT INTERMITTENT
		P1C2A1C	GENERATOR A/D CONVERTER CIRCUIT CIRCUIT VOLTAGE OUT OF RANGE
		P1C2A49	GENERATOR A/D CONVERTER CIRCUIT INTERNAL ELECTRONIC FAILURE
		P1C2B1C	DRIVE MOTOR "A" CONTROL MODULE A/D CONVERTER CIRCUIT VOLTAGE OUT OF RANGE
		P1C2B49	DRIVE MOTOR "A" CONTROL MODULE A/D CONVERTER CIRCUIT INTERNAL ELECTRONIC FAILURE
		P313383	COMMUNICATION ERROR FROM GENERATOR TO DRIVE MOTOR "A" VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT
		P313386	COMMUNICATION ERROR FROM GENERATOR TO DRIVE MOTOR "A" SIGNAL INVALID
		P313387	COMMUNICATION ERROR FROM GENERATOR TO DRIVE MOTOR "A" MISSING MESSAGE
		P313483	COMMUNICATION ERROR FROM DRIVE MOTOR "A" TO GENERATOR VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT
		P313486	COMMUNICATION ERROR FROM DRIVE MOTOR "A" TO GENERATOR SIGNAL INVALID
		P313487	COMMUNICATION ERROR FROM DRIVE MOTOR "A" TO GENERATOR MISSING MESSAGE
	P-HEV Hybrid Powertrain Control	P0A1B49	DRIVE MOTOR "A" CONTROL MODULE INTERNAL ELECTRONIC FAILURE
Power supply system malfunction	P-HEV Drive Motor	P06B01C	GENERATOR CONTROL MODULE POSITION SENSOR REF POWER SOURCE CIRCUIT VOLTAGE OUT OF RANGE
Power supply system malfunction	P-HEV Drive Motor	P06D61C	GENERATOR CONTROL MODULE OFFSET POWER CIRCUIT VOLTAGE OUT OF RANGE
Communication system malfunction	P-HEV Drive Motor	P312487	LOST COMMUNICATION BETWEEN DRIVE MOTOR "A" AND HV ECU MISSING MESSAGE
Communication system malfunction	P-HEV Hybrid Powertrain Control	P312387	LOST COMMUNICATION WITH DRIVE MOTOR CONTROL MODULE "A" FROM HYBRID/EV CONTROL MODULE MISSING MESSAGE

When "Only DTC P0E5128 is displayed" or "DTC other than above is displayed at the same time", go to A.

When DTCs related to [P-HEV Hybrid Powertrain Control] mentioned above are simultaneously displayed, go to B.

When DTCs related to [P-HEV Drive Motor] mentioned above are simultaneously displayed, go to C.

Yes:

Go to 2.
Perform the diagnosis for the simultaneously displayed DTCs.
NOTE: If more than one DTC is simultaneously displayed, perform the diagnosis in the order described in the above.
Perform the diagnosis for the simultaneously displayed DTCs.

NOTE: If more than one DTC is simultaneously displayed, perform the diagnosis in the order described in the above.

No: -

CHECK THE CONNECTING CONDITION OF CONNECTOR (Inverter with converter assembly LOW PRESSURE CONNECTOR) .
CAUTION: Make sure to wear insulated gloves and protective goggles during the work.
1. Check that the Service plug is disconnected. Ref. to HYBRID ELECTRIC VEHICLE>SERVICE PLUG .
2. Check the connecting condition of low pressure connectors (HV23) and (HV24) in Inverter with converter assembly and check the relevant terminals for contact pressure, deformation and intrusion of water or foreign matter. Ref. to HYBRID ELECTRIC VEHICLE>INVERTER AND CONVERTER ASSEMBLY .
NOTE: When connecting the connector, insert to the end with the lock lever raised, then fold the lock lever completely until a click is heard. After connected, make sure that the lock claw does not loosen and pull the connector to see that it does not come off.

Is there looseness at the connector connection, or any poor contact, deformation or intrusion of water or foreign matters at the relevant terminals?

Yes: Connect the connector securely. Or repair the poor contact of connector.

No: Replace Inverter with converter assembly. Ref. to HYBRID ELECTRIC VEHICLE>INVERTER AND CONVERTER ASSEMBLY .