Front Seat ASSY: Disassembly
CAUTION:
(Passenger's seat only)
- The occupant detection control module, occupant detection sensor, front seat cushion pad and front seat cushion frame ASSY are assembled as a front cushion & frame ASSY. Therefore, never remove the occupant detection control module or the occupant detection sensor as a single unit.
- Never disconnect the connector of the occupant detection sensor from the occupant detection control module.
- When replacing the front seat cushion cover, be careful not to damage the occupant detection sensor during hog ring installation.
- Check if the occupant detection system is working normally after removing or replacing a front seat cushion cover or replacing the occupant detection system.
NOTE:
The following procedure is for LH side. Unless otherwise specified, perform the work for the RH side referring to the procedures for the LH side.
- Removal of the reclining adjuster release handle LH
- Pull up the reclining adjuster release handle LH.
- As shown in the figure, release the claw by using the fine flat tip screwdriver wrapped with protective tape, and remove the reclining adjuster release handle LH.
- Removal of the vertical adjuster handle LH (driver's side)
- Remove the screw and remove the vertical adjuster handle LH.
- Removal of the front seat cushion shield LH
- Remove 2 screws.
- Release 4 claws, 5 guides, and the clip, and remove the front seat cushion shield LH.
- Removal of the front seat cushion shield INN LH
- Release 2 claws, 4 guides, and the clip, and remove the front seat cushion shield INN LH.
- Removal of the front seat inner belt ASSY LH (Refer to REMOVAL , Step 4)
- Removal of the front seat backrest ASSY LH
- Release 2 hooks.
- Remove the rubber band of the separate type front seat backrest cover LH.
- Disconnect the connector and the clamp of the seat heater. (For the model with the seat heater)
- Release the fastener and disconnect the wiring harness of the side airbag module LH.
- Release the claw and 4 clamps, and disconnect the wiring harness of the side airbag module ASSY LH.
- Using the torque socket wrench (T40), remove 4 bolts, and remove the front seat backrest ASSY LH from the front seat cushion ASSY LH.
- Release 2 hooks.
- Removal of the separate type front seat backrest cover with pad
- Remove 5 hog rings.
- Open 2 fasteners.
- Turn over the separate type front seat backrest cover LH.
- Release 2 hooks.
- Remove the nut, and disconnect 3 brackets of the separate type front seat backrest cover LH.
- Release 4 claws and remove 2 front seat headrest supports.
- Remove the separate type front seat backrest cover with pad from the separate type front seat backrest frame ASSY LH.
- Remove 5 hog rings.
- Removal of the side airbag module LH (Refer to REMOVAL )
- Removal of the separate type front seat backrest cover LH
- Remove 14 hog rings, and remove the separate type front seat backrest cover LH from the separate type front seat backrest pad LH.
- Removal of the separate type front seat cushion cover with pad
- Release the claw and 3 clamps, and disconnect the wiring harness of the seat heater. (For the model with the seat heater)
- Release the hooks, and remove the separate type front seat cushion cover with pad from the separate type front seat cushion frame ASSY LH. (driver's side)
- Release the claw and 3 clamps, and disconnect the wiring harness of the seat heater. (For the model with the seat heater)
- Removal of the separate type front seat cushion cover LH
- Remove 2 hog rings.
- Remove 12 hog rings, and remove the separate type front seat cushion cover LH from the separate type front seat cushion pad LH.
- Remove 2 hog rings.
- Removal of the front seat cushion shield LWR LH (driver's side)
- Remove the screw.
- Release the hook.
- Release the clip, and remove the front seat cushion shield LWR LH.
- Removal of the front seat cushion shield LWR LH (driver's side)NOTE: Remove the part in the same manner as RH side.
- Removal of the front seat cushion edge protector LH
- Remove the screw.
- Release 3 claws and remove the front seat cushion edge protector LH.
- Removal of the front seat cushion edge protector LHNOTE: Remove the part in the same manner as RH side.
- Removal of the seat track adjusting handle
- Remove 2 springs with a screwdriver, and remove the seat track adjusting handle from the separate type front seat cushion frame ASSY LH.
- Removal of the reclining adjuster release band (Passenger's side)
- Remove the screw and remove the reclining adjuster release band.
- Removal of the seat track cover OUT RH
- Release 2 claws and remove the seat track cover OUT RH.
NOTE: Remove both parts using the same procedures. - Removal of the front seat cushion protector No. 1
- Release 2 claws and remove the front seat cushion protector No. 1.NOTE: Remove both parts using the same procedures.
- Release 2 claws and remove the front seat cushion protector No. 1.