Interior Collation Does Not Function

CAUTION: When the access key or keyless access CM is replaced, registration of the immobilizer is required. For the relevant procedures, refer to the "REGISTRATION MANUAL FOR IMMOBILIZER" provided as a separate volume. Contact an authorized Subaru Dealership.

CHECK ACCESS KEY.
Check the battery of the access key. Ref. to SECURITY AND LOCKS>Access Key>INSPECTION .

Is the check result OK?
- Yes : Go to 2.
- No : Replace the battery.
CHECK INTERIOR ANTENNA.
1. Using the Subaru Select Monitor, select the system check [Front interior transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Using a tester, check the output between keyless access CM connector terminals while performing the Keyless access system check.
  Connector & terminal
  
  (B574) No. 2 - (B574) No. 3:
Is a pulse output?
- Yes : Go to 3.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .
CHECK INTERIOR ANTENNA.
1. Using the Subaru Select Monitor, select the system check [Rear interior transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Using a tester, check the output between keyless access CM connector terminals while performing the Keyless access system check.
  Connector & terminal
  
  (B573) No. 10 - (B573) No. 11:
Is a pulse output?
- Yes : Go to 4.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .
CHECK INTERIOR ANTENNA.
1. Using the Subaru Select Monitor, select the system check [Trunk internal transmitter, interior tuner] or [Rear gate internal transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Using a tester, check the output between keyless access CM connector terminals while performing the Keyless access system check.
  Connector & terminal
  
  (B573) No. 8 - (B573) No. 9:
Is a pulse output?
- Yes : Go to 5.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .
CHECK WIRING HARNESS (OPEN).
1. Disconnect the front interior antenna connector and the keyless access CM connector.
2. Using a tester, check continuity between the front interior antenna connector and the keyless access CM connector.
  Connector & terminal
  
  (B579) No. 1 - (B574) No. 3:
  
  (B579) No. 3 - (B574) No. 2:
Is there continuity?
- Yes : Go to 6.
- No : Repair or replace the open circuit of harness.
CHECK WIRING HARNESS (OPEN).
1. Disconnect the center interior antenna connector and the keyless access CM connector.
2. Using a tester, check continuity between the center interior antenna connector and the keyless access CM connector.
  Connector & terminal
  
  (R298) No. 1 - (B573) No. 11:
  
  (R298) No. 3 - (B573) No. 10:
Is there continuity?
- Yes : Go to 7.
- No : Repair or replace the open circuit of harness.
CHECK WIRING HARNESS (OPEN).
1. Disconnect the rear interior antenna connector and the keyless access CM connector.
2. Using a tester, check continuity between the rear interior antenna connector and the keyless access CM connector.
  Connector & terminal
  
  (R297) No. 1 - (B573) No. 9:
  
  (R297) No. 3 - (B573) No. 8:
Is there continuity?
- Yes : Go to 8.
- No : Repair or replace the open circuit of harness.
CHECK ANTENNA.
Replace the front interior antenna with a new or properly functioning part. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

Does it operate properly?
- Yes : Replace the front interior antenna. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .
- No : Go to 9.
CHECK ANTENNA.
Replace the center passenger room antenna with a new or properly functioning part. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

Does it operate properly?
- Yes : Replace the center passenger room antenna. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .
- No : Go to 10.
CHECK ANTENNA.
Replace the rear interior antenna with a new or properly functioning part. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

Does it operate properly?
- Yes : Replace the rear interior antenna. Ref. to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .
- No : Go to 11.
CHECK WIRING HARNESS (OPEN).
1. Disconnect the receiver connector and the keyless access CM connector.
2. Using a tester, check continuity between the receiver connector and keyless access CM connector.
  Connector & terminal
  
  (R296) No. 4 - (B573) No. 5:
  
  (R296) No. 5 - (B573) No. 17:
  
  (R296) No. 2 - (B573) No. 19:
Is there continuity?
- Yes : Go to 12.
- No : Repair or replace the open circuit of harness.
CHECK RECEIVER.
Replace the receiver with a new or properly functioning part. Ref. to SECURITY AND LOCKS>Receiver>REMOVAL .

Does it operate properly?
- Yes : Replace the receiver. Ref. to SECURITY AND LOCKS>Receiver>REMOVAL .
- No : Go to 13.
CHECK KEYLESS ACCESS SYSTEM CHECK.
1. Using the Subaru Select Monitor, select the system check [Front interior transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Hold the access key 1 m or more away from the audio panel, then come closer to within 0.8 m.
Does the buzzer sound?
- Yes : Go to 14.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .
CHECK KEYLESS ACCESS SYSTEM CHECK.
1. Using the Subaru Select Monitor, select the system check [Rear interior transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Hold the access key 1 m or more away from the center of the second row seats, then come closer to within 0.8 m.
Does the buzzer sound?
- Yes : Go to 15.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .
CHECK KEYLESS ACCESS SYSTEM CHECK.
1. Using the Subaru Select Monitor, select the system check [Trunk internal transmitter, interior tuner] or [Rear gate internal transmitter, interior tuner] of [Keyless Access with Push Button Start]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>Keyless Access System Check .
2. Hold the access key 1 m or more away from the back of the rear seat, then come closer to within 0.8 m.
Does the buzzer sound?
- Yes : System is normal.
- No : Replace the keyless access CM. Ref. to SECURITY AND LOCKS>Keyless Access CM>REMOVAL .