Intake Side
WARNING: This page is about a different car, the 2006 Subaru Outback. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
- Adjustment of valve clearance should be performed while engine is cold.
- Do not wear gloves during removal and installation of valve lifter.
- Do not use valve lifters that were dropped or otherwise exposed to strong impacts.
- When installing the valve lifter, align the anti-rotation of valve lifter with groove on cylinder head, and then insert the valve lifter.
- Measure all the valve clearances.
< Ref. to INSPECTION , Valve Clearance. >
NOTE: Record each valve clearance after measurement. - Remove the camshaft. < Ref. to REMOVAL , Camshaft. >
- Remove the valve lifter.
- Remove the shim from valve lifter.
- Check the thickness of the shim from the markings on the side of the shim that was removed.
- Select a shim of suitable thickness from the following table using the measured valve clearance and shim thickness.
SHIM THICKNESS SPECIFICATION
| Unit: (mm) |
| S = (V + T) - 0.20 |
| S: Required shim thickness V: Measured valve clearance T: Shim thickness to be used |
SHIM THICKNESS SPECIFICATION
| Part No. | Thickness mm (in) |
|---|---|
| 13218AK890 | 1.92 (0.0756) |
| 13218AK900 | 1.94 (0.0764) |
| 13218AK910 | 1.96 (0.0772) |
| 13218AK920 | 1.98 (0.0780) |
| 13218AK930 | 2.00 (0.0787) |
| 13218AK940 | 2.02 (0.0795) |
| 13218AK950 | 2.04 (0.0803) |
| 13218AK960 | 2.06 (0.0811) |
| 13218AK970 | 2.07 (0.0815) |
| 13218AK980 | 2.08 (0.0819) |
| 13218AK990 | 2.09 (0.0823) |
| 13218AL000 | 2.10 (0.0827) |
| 13218AL010 | 2.11 (0.0831) |
| 13218AL020 | 2.12 (0.0835) |
| 13218AL030 | 2.13 (0.0839) |
| 13218AL040 | 2.14 (0.0843) |
| 13218AL050 | 2.15 (0.0846) |
| 13218AL060 | 2.16 (0.0850) |
| 13218AL070 | 2.17 (0.0854) |
| 13218AL080 | 2.18 (0.0858) |
| 13218AL090 | 2.19 (0.0862) |
| 13218AL100 | 2.20 (0.0866) |
| 13218AL110 | 2.21 (0.0870) |
| 13218AL120 | 2.22 (0.0874) |
| 13218AL130 | 2.23 (0.0878) |
| 13218AL140 | 2.24 (0.0882) |
| 13218AL150 | 2.25 (0.0886) |
| 13218AL160 | 2.26 (0.0890) |
| 13218AL170 | 2.27 (0.0894) |
| 13218AL180 | 2.28 (0.0898) |
| 13218AL190 | 2.29 (0.0902) |
| 13218AL200 | 2.30 (0.0906) |
| 13218AL210 | 2.31 (0.0909) |
| 13218AL220 | 2.32 (0.0913) |
| 13218AL230 | 2.33 (0.0917) |
| 13218AL240 | 2.34 (0.0921) |
| 13218AL250 | 2.35 (0.0925) |
| 13218AL260 | 2.36 (0.0929) |
| 13218AL270 | 2.37 (0.0933) |
| 13218AL280 | 2.38 (0.0937) |
| 13218AL290 | 2.39 (0.0941) |
| 13218AL300 | 2.40 (0.0945) |
| 13218AL310 | 2.41 (0.0949) |
| 13218AL320 | 2.42 (0.0953) |
| 13218AL330 | 2.43 (0.0957) |
| 13218AL340 | 2.44 (0.0961) |
| 13218AL350 | 2.45 (0.0965) |
| 13218AL360 | 2.46 (0.0969) |
| 13218AL370 | 2.47 (0.0972) |
| 13218AL380 | 2.48 (0.0976) |
| 13218AL390 | 2.49 (0.0980) |
| 13218AL400 | 2.50 (0.0984) |
| 13218AL410 | 2.51 (0.0988) |
| 13218AL420 | 2.52 (0.0992) |
| 13218AL430 | 2.53 (0.0996) |
| 13218AL440 | 2.54 (0.1000) |
| 13218AL450 | 2.55 (0.1004) |
| 13218AL460 | 2.56 (0.1008) |
| 13218AL470 | 2.57 (0.1012) |
| 13218AL480 | 2.58 (0.1016) |
| 13218AL490 | 2.59 (0.1020) |
| 13218AL500 | 2.60 (0.1024) |
| 13218AL510 | 2.61 (0.1028) |
| 13218AL520 | 2.62 (0.1032) |
| 13218AL530 | 2.64 (0.1039) |
| 13218AL540 | 2.66 (0.1047) |
| 13218AL550 | 2.68 (0.1055) |
| 13218AL560 | 2.70 (0.1063) |
| 13218AL570 | 2.72 (0.1071) |
| 13218AL580 | 2.74 (0.1079) |
| 13218AL590 | 2.76 (0.1087) |