Check values for propeller shaft alignment sleeve - BE41.10-P-1000-02M
WARNING: This page does not describe the selected car, but rather 33 other vehicles, including the 2016 Mercedes-Benz E63 S AMG, 2016 Mercedes-Benz E400, 2016 Mercedes-Benz E350, 2016 Mercedes-Benz E300, and 2016 Mercedes-Benz E250. However, it is still accessible from the selected car via links, so may be relevant.
MODEL 204, 207, 212, 218
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 204.001/201 | MODEL 204.000/002/200/20 2 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 24, 8 |
| Rear propeller shaft | mm | 36, 2 | 36, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 204.003 with autom. transmission | Model 204.006/007/041/044/045/046/048/049/052/054/081/082/085/087/089/092/207/241/245/246/248/249/252/254/282/289/292/981/982/983/984/987/992 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 23, 3 |
| Rear propeller shaft | mm | 36, 2 | 26, 8 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 204.008/047/056/065/208/247/256/901/90 2/956 | MODEL 204.022/025/222/22 5 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 28, 8 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 204.077/277 | MODEL 204.003 with manual transmission | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 28, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 8 | 36, 2 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 207.302/402 | MODEL 207.303/403 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 36, 3 | 36, 2 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 207.322/372/422/472 | MODEL 207.347/356/357/44 7/456/457 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 24, 8 |
| Rear propeller shaft | mm | 28, 8 | 28, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 207.348/448 | MODEL 212.002/005/202/205 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 23, 3 | 24, 8 |
| Rear propeller shaft | mm | 26, 8 | 36, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 212.024/025/224/225 with autom. transmission | MODEL 212.047/093/247/293 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 24, 8 |
| Rear propeller shaft | mm | 36, 2 | 28, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 212.041/048/054/082/087/089/090/147/14 8/248/254/282/287/2 88/289 | MODEL 212.053/056/057/256/257 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 23, 3 | 36, 3 |
| Rear propeller shaft | mm | 26, 8 | 28, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 212.024/025/224/225 with manual transmission | MODEL 212.154 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 34, 8 |
| Rear propeller shaft | mm | 28, 8 | 26, 8 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 218.303/323/373 | MODEL 218.359 without CODE 460 (Additional parts, Canadian vehicles) without CODE 494 (US version) | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 25, 3 | 36, 3 |
| Rear propeller shaft | mm | 28, 8 | 28, 3 | ||
CHECK VALUES FOR PROPELLER SHAFT CENTERING SLEEVE
| Number | Designation | MODEL 218.359 with CODE 460 (Additional parts, Canadian vehicles) with CODE 494 (US version) MODEL 218.391 | MODEL 218.374 | ||
|---|---|---|---|---|---|
| BE41.10-P-1001-02M | Press-in dimension "a" from face end of centering sleeve to joint flange | Front propeller shaft | mm | 24, 8 | 25, 3 |
| Rear propeller shaft | mm | 28, 3 | 36, 2 | ||