LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2009 >> xD Standard >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (U341E Automatic Transaxle) >> Differential Oil Seal >> Replacement

Differential Oil Seal: Replacement

WARNING: This page is about a different variant/trim than selected.
  1. REMOVE ENGINE UNDER COVER 
  2. DRAIN AUTOMATIC TRANSAXLE FLUID 
    1. Remove the drain plug and gasket, and drain the ATF.
    2. Install a new gasket and the drain plug.

      Torque: 49 N*m (500 kgf*cm, 36 ft.*lbf) 

  3. REMOVE FRONT WHEEL 
  4. REMOVE FRONT AXLE HUB NUT  (See REMOVAL )
  5. SEPARATE FRONT SPEED SENSOR  (See REMOVAL )
  6. SEPARATE FRONT STABILIZER LINK ASSEMBLY  (See REMOVAL )
  7. SEPARATE TIE ROD END SUB-ASSEMBLY  (See REMOVAL )
  8. SEPARATE FRONT LOWER SUSPENSION ARM  (See REMOVAL )
  9. SEPARATE FRONT AXLE ASSEMBLY  (See REMOVAL )
  10. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH  (See DISASSEMBLY )
  11. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH  (See DISASSEMBLY )
  12. REMOVE FRONT TRANSAXLE CASE OIL SEAL 
    1. Using SST, remove the front transaxle case oil seal.

      SST 09308-00010 

      Fig 1: Removing Front Transaxle Case Oil Seal
      G05400041Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE TRANSAXLE CASE OIL SEAL 
    1. Using SST, remove the transaxle case oil seal.

      SST 09308-00010 

      Fig 2: Removing Transaxle Case Oil Seal
      G05400042Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL TRANSAXLE CASE OIL SEAL 
    1. Coat the lip of a new transaxle case oil seal with MP grease.
    2. Using SST and a hammer, install the transaxle case oil seal.

      SST 09710-20011 (09710-06071), 09950-70010 (09951-07200) 

      Drive in depth: 

      2.2 to 3.2 mm (0.087 to 0.126 in.) 

      NOTE: Do not damage the oil seal lip.
      Fig 3: Installing Transaxle Case Oil Seal
      G05400043Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL FRONT TRANSAXLE CASE OIL SEAL 
    1. Coat the lip of a new front transaxle case oil seal with MP grease.
    2. Using SST and a hammer, install the front transaxle case oil seal.

      SST 09554-14010, 09950-70010 (09951-07200) 

      Drive in depth:

      -0.5 to 0.5 mm (-0.020 to 0.020 in.)

      NOTE: Do not damage the oil seal lip.
      Fig 4: Installing Front Transaxle Case Oil Seal
      G05400044Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH  (See INSTALLATION )
  17. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH  (See INSTALLATION )
  18. INSTALL FRONT AXLE ASSEMBLY  (See INSTALLATION )
  19. INSTALL FRONT LOWER SUSPENSION ARM  (See INSTALLATION )
  20. INSTALL TIE ROD END SUB-ASSEMBLY  (See INSTALLATION )
  21. INSTALL FRONT STABILIZER LINK ASSEMBLY  (See INSTALLATION )
  22. INSTALL FRONT SPEED SENSOR  (See INSTALLATION )
  23. INSTALL FRONT AXLE HUB NUT  (See INSTALLATION )
  24. INSTALL FRONT WHEEL 

    Torque: 103 N*m (1050 kgf*cm, ft.*lbf) 

  25. ADD AUTOMATIC TRANSAXLE FLUID 
  26. INSPECT AUTOMATIC TRANSAXLE FLUID  (See ON-VEHICLE INSPECTION  )
  27. INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK 
  28. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT 

    HINT:

    (See ADJUSTMENT )

  29. INSTALL ENGINE UNDER COVER 

    Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

scientia non olet · About LEMON Manuals