LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2009 >> xB Automatic >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior >> Roof Headlining >> Removal

Roof Headlining: Removal

CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See PRECAUTION ).
  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    CAUTION: Wait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.
  2. REMOVE REAR FLOOR CARPET ASSEMBLY 
    1. Release the 2 knobs and remove the rear floor carpet.
      Fig 1: Identifying Rear Floor Carpet And Knobs
      G05391876Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE REAR DECK FLOOR BOX 
    1. Remove the rear deck floor box.
      Fig 2: Identifying Rear Deck Floor Box
      G05391877Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE DECK FLOOR BOX RH 
    1. Remove the 2 nuts and remove the deck floor box.
      Fig 3: Locating Deck Floor Box Nuts
      G05391878Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE DECK FLOOR BOX LH 
    1. Remove the 2 nuts and remove the deck floor box.
    Fig 4: Locating Deck Floor Box Nuts
    G05391879Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE REAR SEAT CUSHION WITH COVER PAD SUB-ASSEMBLY  (See REMOVAL )
  7. REMOVE REAR SEATBACK ASSEMBLY RH  (See REMOVAL )
  8. REMOVE REAR SEATBACK ASSEMBLY LH  (See REMOVAL )
  9. REMOVE FRONT DOOR SCUFF PLATE RH 
    1. Disengage the 10 claws and remove the front door scuff plate.
    Fig 5: Identifying Front Door Scuff Plate LH And Claws
    G05391880Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE FRONT DOOR SCUFF PLATE LH 

    HINT:

    Use the same procedure as for the RH side.

  11. REMOVE COWL SIDE TRIM BOARD RH 
    1. Disengage the clip, claw and guide and remove the cowl side trim board.
    Fig 6: Identifying Cowl Side Trim Board Clip
    G05391881Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE COWL SIDE TRIM BOARD LH 

    HINT:

    Use the same procedure as for the RH side.

  13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Remove the front door opening trim weatherstrip.
  14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 7: Identifying Front Door Opening Trim Weatherstrip
    G05391882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE REAR DOOR SCUFF PLATE RH 
    1. Disengage the 8 claws and remove the rear door scuff plate.
  16. REMOVE REAR DOOR SCUFF PLATE LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 8: Identifying Rear Door Scuff Plate LH And Claws
    G05391883Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Remove the rear door opening trim weatherstrip.
  18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 9: Identifying Rear Door Opening Trim Weatherstrip
    G05391884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE REAR DECK TRIM COVER 
    1. Disengage the 4 clips, 4 claws and 2 guides and remove the rear deck trim cover.
      Fig 10: Identifying Clips, Claws And Guides
      G05391885Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY 

    HINT:

    Use the same procedure for both sides.

    1. Remove the 2 bolts and 2 luggage hold belt strikers.
      Fig 11: Locating Bolts And Luggage Hold Belt Strikers
      G05391886Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE REAR SEAT BACK HINGE 

    HINT:

    Use the same procedure for both sides.

    1. Remove the bolt and rear seat back hinge.
      Fig 12: Locating Bolt And Rear Seat Back Hinge
      G05391887Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH 
    1. Remove the belt from the rear seat shoulder belt hanger
    2. Remove the bolt and floor anchor
  23. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side

    Fig 13: Locating Bolt And Floor Anchor
    G05391888Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. Using a clip remover, remove the clip.
    2. Disengage the 6 clips and 7 claws and remove the deck trim side panel.
      Fig 14: Identifying Deck Trim Side Panel Assembly RH And Clip
      G05391889Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. Using a clip remover, remove the clip.
    2. Disengage the 6 clips and 7 claws and remove the deck trim side panel
    3. Disconnect the luggage compartment light connector
      Fig 15: Identifying Deck Trim Side Panel, Clips And Claws
      G05391890Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH 
    1. Using a clip remover, remove the clip.
    2. Disengage the 7 clips and remove the roof side inner garnish.
    3. Pass the rear seat outer belt through the slit in the roof side inner garnish.
  27. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 16: Identifying Roof Side Inner Garnish And Clips
    G05391891Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. REMOVE SEAT BELT ANCHOR COVER CAP 

    HINT:

    Use the same procedure for both sides.

    1. Pull portion A, shown in the illustration, toward you, remove the 2 claws on the lower side followed by the claw on the upper side. Then remove the seat belt anchor cover cap.
      Fig 17: Identifying Seat Belt Anchor Cover Cap
      G05391892Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Remove the bolt and through anchor.
  30. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 18: Identifying Through Anchor Bolt
    G05391893Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. REMOVE CENTER PILLAR LOWER GARNISH RH 
    1. Disengage the 2 clips, 3 claws and guide and remove the center pillar lower garnish.
  32. REMOVE CENTER PILLAR LOWER GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 19: Identifying Clips, Claws And Guide
    G05391894Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE CENTER PILLAR UPPER GARNISH RH 
    1. Disengage the 2 clips and guide and remove the center pillar upper garnish.
  34. REMOVE CENTER PILLAR UPPER GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 20: Identifying Center Pillar Upper Garnish Clips
    G05391895Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE FRONT PILLAR GARNISH RH NOTICE: 
    • Install a protective cover onto the curtain shield airbag as soon as the front pillar garnish is removed.
    • Replace the front pillar garnish clip with a new one when the front pillar garnish is removed.
    1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
      Fig 21: Removing Front Pillar Garnish
      G00480933Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Cut off clip A.
    3. Disengage the 2 clips and 2 guides and remove the front pillar garnish.
    4. Remove clip A from the vehicle body.
    5. Completely coyer the curtain shield airbag with a piece of cloth or nylon and fix the ends of the protective cover with adhesive tape, as shown in the illustration.

      Protective cover size

      PROTECTIVE COVER SIZE SPECIFICATION

      Area Measurement
      a 700 mm (27.56 in.)
      b 120 mm (4.72 in.)
      Fig 22: Identifying Protective Cover With Adhesive Tape
      G05391897Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE FRONT PILLAR GARNISH LH 

    HINT:

    Use the same procedure as for the RH side.

  37. REMOVE ASSIST GRIP 

    HINT:

    Use the same procedure to remove all assist grips.

    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 assist grip covers.
      Fig 23: Removing Assist Grip Covers
      G04835383Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 2 clips and remove the assist grip
      Fig 24: Identifying Assist Grip And Clip
      G05391899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. REMOVE VISOR ASSEMBLY RH 
    1. Using a screwdriver, with its tip wrapped in protective tape, disengage the 4 claws and remove the visor cover
      Fig 25: Removing Visor Assembly RH
      G05391900Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the visor shaft from the visor holder.
    3. Disengage the 2 clips and remove the visor.
  39. REMOVE VISOR ASSEMBLY LH 

    HINT:

    Use the same procedure as for the RH side.

    Fig 26: Locating Visor Holder And Clips
    G05391901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  40. REMOVE VISOR HOLDER 

    HINT:

    Use the same procedure as for the RH side.

    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.
    2. Disengage the 2 claws and remove the visor holder.
      Fig 27: Removing Visor Holder
      G05391902Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  41. REMOVE ROOM LIGHT ASSEMBLY 
    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light lens.
      Fig 28: Removing Room Light Assembly
      G05391903Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the 2 room light covers.
      Fig 29: Removing Room Light Covers
      G05391904Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light.
      Fig 30: Disengaging Claws
      G04835391Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the roof wire from the claw on the room light.
    5. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws and remove the room light switch base.
      Fig 31: Removing Room Light Switch Base And Room Light
      G04835490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  42. REMOVE MAP LIGHT ASSEMBLY 
    1. Using a molding remover D, disengage the 4 claws and remove the map light.
      Fig 32: Identifying Map Light Claws
      G00480934Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the map light connector
  43. REMOVE INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY  (See REMOVAL )
  44. REMOVE INSTRUMENT CLUSTER FINISH LOWER PANEL  (See REMOVAL )
    Fig 33: Connecting Map Light Connector
    G04835492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY  (See REMOVAL )
  46. REMOVE COMBINATION METER ASSEMBLY  (See REMOVAL )
  47. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY  (See REMOVAL )
  48. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY  (See REMOVAL )
  49. REMOVE ROOF HEADLINING 
    1. Disconnect the antenna cord connector
    2. Using a clip remover, disengage the 4 clamps.
      Fig 34: Identifying Roof Headlining Clamps
      G05391909Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the roof wire connector
    4. Disconnect the roof wire from the harness clamp.
    5. Using a clip remover, disengage the 5 clamps.
      Fig 35: Locating Roof Wire Connector Clamps
      G05391910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the 2 connectors.
    7. Remove the bolt and bracket.
      Fig 36: Locating Connectors, Bolt And Bracket
      G05391911Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Using a clip remover, remove the 5 clips.
      Fig 37: Identifying Clips
      G05391912Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Remove the roof headlining from the back door.
      Fig 38: Removing Roof Headlining Of Back Door
      G05391913Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  50. REMOVE NO. 1 ROOF SILENCER 
    1. Remove the 2 No. 1 roof silencers.
      Fig 39: Locating No. 1 Roof Silencers
      G05391914Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  51. REMOVE NO. 3 ROOF PANEL PAD 
    1. Remove the No 3 roof panel pad.
      Fig 40: Locating No 3 Roof Panel Pad
      G05391915Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  52. REMOVE NO. 4 ROOF PANEL PAD 
    1. Remove the No 4 roof panel pad
      Fig 41: Locating No 4 Roof Panel Pad
      G05391916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  53. REMOVE NO. 1 ROOF SILENCER PAD 
    1. Remove the 5 No. 1 roof silencer pads.
      Fig 42: Locating No. 1 Roof Silencer Pads
      G05391917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  54. REMOVE ROOF HEADLINING PAD RH 
    1. Remove the 8 adhesive portions and the roof headlining pad.
      Fig 43: Identifying Roof Headlining Pad
      G05391918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  55. REMOVE ROOF HEADLINING PAD LH 
    1. Remove the 8 adhesive portions and the roof headlining pad
      Fig 44: Identifying Adhesive Portions And Roof Headlining Pad
      G05391919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  56. REMOVE FRONT SIDE RAIL SPACER RH 
    1. Remove the 2 adhesive portions and the front side rail spacer.
  57. REMOVE FRONT SIDE RAIL SPACER LH 

    HINT:

    Use the same procedure as for the RH side

    Fig 45: Identifying Adhesive Portions And Front Side Rail Spacer
    G05391920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  58. REMOVE ROOF WIRE 
    1. Remove the 10 pieces of tape.
    2. Remove the roof wire from the roof headlining.
    Fig 46: Identifying Roof Wire
    G05391921Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  59. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY  (See REMOVAL )
scientia non olet · About LEMON Manuals