Rear Seat Outer Belt Assembly: Installation

HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.

1. INSTALL SEAT BELT HOLE SEAL 
   1. Engage the 2 claws and install the seat belt hole seal.
      Fig 1: Identifying Seat Belt Hole Seal

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL REAR SEAT OUTER BELT ASSEMBLY 
   1. Check the angle of inclination required to lock the retractor.
      1. Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.
         NOTE: Do not disassemble the retractor. If the operation is not as specified, replace the rear seat outer belt.
         Fig 2: Identifying Rear Seat Outer Belt Lock And Unlock Position

         Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Hook the lower stay of the retractor onto the 2 body hooks and install the retractor with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      Fig 3: Locating Hooks And Retractor With Bolts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Install the through anchor with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      Fig 4: Locating Anchor Bolt

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   4. Check that the ELR locks.
      NOTE: Perform the check with the rear seat outer belt installed.
      1. With the belt installed, check that the belt locks when it is pulled out quickly.

         If the operation is not as specified, replace the rear seat outer belt.

3. INSTALL ROOF SIDE INNER GARNISH  (See INSTALLATION )
4. INSTALL REAR SEAT SHOULDER BELT HANGER 
   1. Engage the 2 claws and install the rear seat shoulder belt hanger.
      Fig 5: Identifying Rear Seat Shoulder Belt Hanger Claws

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY 
   1. Engage the 3 clips and the 7 claws and install the deck trim side panel.
   Fig 6: Locating Clips And Claws
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Tighten the screw.
   3. Engage the clip and install the rear seat outer belt anchor plate.
   Fig 7: Locating Rear Seat Outer Belt Anchor Plate
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   4. Tighten the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

   5. Install the belt of the rear seat outer belt into the rear seat shoulder belt hanger.
   Fig 8: Locating Rear Seat Shoulder Belt Hanger
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY  (See REMOVAL )
7. INSTALL REAR DECK TRIM COVER  (See INSTALLATION )
8. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP 
   1. Install the rear door opening trim weatherstrip.
   Fig 9: Identifying Rear Door Opening Trim Weatherstrip
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. INSTALL REAR DOOR SCUFF PLATE  (See INSTALLATION )
10. INSTALL REAR SEAT ASSEMBLY RH  (See INSTALLATION )
11. INSTALL REAR SEAT ASSEMBLY LH  (See INSTALLATION )
12. INSTALL NO. 2 REAR SEAT LEG COVER (for LH Side)  (See INSTALLATION )
13. INSTALL NO. 1 REAR SEAT LEG COVER (for LH Side)  (See INSTALLATION )
14. INSTALL NO. 1 REAR SEAT LEG COVER (for RH Side)  (See INSTALLATION )
15. INSTALL DECK BOARD ASSEMBLY  (See INSTALLATION )