LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2008 >> xB Standard >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Meter >> Meter / Gauge System >> Warning Buzzer does not Sound >> Inspection Procedure

Inspection Procedure

  1. CHECK BUZZER (SEAT BELT, KEY REMINDER, TAILLIGHT REMINDER) 
    1. Check that the seat belt, key reminder and taillight reminder warning buzzers sound.

      Result 

      RESULT CHART

      Result Proceed to
      Seat belt warning buzzer does not sound (where equipped with seat belt warning system) A
      Key reminder warning buzzer does not sound (where equipped with key reminder warning system) B
      Taillight reminder warning buzzer does not sound (Meter illuminations normal) C
      No warning buzzers sound D

      HINT:

      • Seat belt warning buzzer on: Ignition switch is on (IG), driver or front passenger seat belt is unfastened, and vehicle speed is 12.4mph (20 km/h) or more.
      • Key reminder warning buzzer on: Ignition switch is off, key is in ignition key cylinder, and driver side door is open.
      • Taillight reminder warning buzzer on: Ignition switch is off, taillight relay switch is on (IG), and driver side door is open.

    B:  Go to step  5

    C:  Go to step  11

    D : REPLACE COMBINATION METER ASSEMBLY  (See REMOVAL  )

    A: Go to next step 

  2. CHECK SUPPLEMENTAL RESTRAINT SYSTEM 
    1. Connect an intelligent tester or a Techstream to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD / MOBD / CENTER AIRBAG SENSOR / DTC INFO
      2. Techstream - Select: Body / Center airbag sensor / Trouble Codes.

        Result 

        RESULT CHART

        Result Proceed to
        No SRS DTCs are output A
        SRS DTCs are output B

    B: Go TO  SUPPLEMENTAL RESTRAINT SYSTEM  .

    A: Go to next step 

  3. CHECK OCCUPANT CLASSIFICATION SYSTEM 
    1. Connect an intelligent tester or a Techstream to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD / MOBD / OCCUPANT DETECTION / DTC INFO.
      2. Techstream - Select: Body / Occupant Detection / Trouble Codes.

        Result 

        RESULT CHART

        Result Proceed to
        No occupant classification system DTCs are output A
        Occupant classification system DTCs are output B

    B: Go TO  OCCUPANT CLASSIFICATION SYSTEM  .

    A: Go to next step 

  4. CHECK KEY REMINDER FUNCTION 
    1. Ignition switch is off.
    2. Key is in ignition key cylinder.
    3. Driver side door is open.

      OK: 

      Key reminder warning buzzer ON. 

    NG : REPLACE COMBINATION METER ASSEMBLY  (See REMOVAL  ).

    OK : REPLACE MAIN BODY ECU  (See REMOVAL )

  5. READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)) 
    1. Connect an intelligent tester or a Techstream to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Operate the intelligent tester or Techstream according to the display and select "DATA LIST" or "Data List" (See DATA LIST / ACTIVE TEST  ).
      1. Intelligent tester

        Body / Main Body / DATA LIST: 

        BODY / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        D DOR CTY SW Driver side door courtesy light switch signal ON or OFF ON: Driver side door is open
        OFF: Driver side door is closed        		 -
      2. Techstream

        Body Electrical / Main Body / Data List: 

        BODY ELECTRICAL / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        D Door Courtesy SW Driver side door courtesy light switch signal ON or OFF ON: Driver side door is open
        OFF: Driver side door is closed        		 -

    NG:  Go to step  9

    OK: Go to next step 

  6. READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (UNLOCK WARNING SWITCH) 
    1. Connect an intelligent tester or a Techstream to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Operate the intelligent tester or Techstream according to the display and select "DATA LIST" or "Data List" (See DATA LIST / ACTIVE TEST  ).
      1. Intelligent tester

        Body / Main Body / DATA LIST: 

        BODY / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        KEY UNLK WRN SW Unlock warning switch signal ON or OFF ON: Key is in ignition key cylinder
        OFF: No key is in ignition key cylinder        		 -
      2. Techstream

        Body Electrical / Main Body / Data List: 

        BODY ELECTRICAL / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        Key Unlock Warning SW Unlock warning switch signal ON or OFF ON: Key is in ignition key cylinder
        OFF: No key is in ignition key cylinder        		 -

    NG: Go to step 7 

    OK : REPLACE COMBINATION METER ASSEMBLY  (See REMOVAL  ).

  7. INSPECT UNLOCK WARNING SWITCH ASSEMBLY 
    1. Remove the unlock warning switch assembly (See REMOVAL ).
    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      1 - 2 Not pushed 10 kΩ or higher
      1 - 2 Pushed Below 1 Ω
      Fig 1: Identifying Unlock Warning Switch Assembly Connector Terminals
      G05391135Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reinstall the unlock warning switch assembly (See INSTALLATION ).

    NG : REPLACE UNLOCK WARNING SWITCH ASSEMBLY  (See REMOVAL ).

    OK: Go to next step 

  8. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU) 
    1. Disconnect the C6 unlock warning switch assembly connector
    2. Disconnect the 2E main body ECU connector
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      C6-1 - 2E-23 (KSW) Always Below 1 Ω
      C6-2 - Body ground Always Below 1 Ω
      Fig 2: Checking Harness And Connector (Unlock Warning Switch Assembly - Main Body ECU)
      G05391136Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Reconnect the unlock warning switch assembly connector
    5. Reconnect the main body ECU connector.

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : REPLACE MAIN BODY ECU  (See REMOVAL ).

  9. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE) 
    1. Disconnect the H1 front door courtesy light switch LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      H1-1 - Body ground Not pushed (ON) Below 1 Ω
      H1-1 - Body ground Pushed (OFF) 10 kΩ or higher
      Fig 3: Identifying Door Courtesy Light Switch
      G04833360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the front door courtesy light switch LH connector.

    NG : REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)  (See REMOVAL ).

    OK: Go to next step 

  10. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU) 
    1. Disconnect the H1 front door courtesy light switch connector.
    2. Disconnect the 2A main body ECU connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      H1-1 - 2A-21 (DCTY) Always Below 1 Ω
      Fig 4: Identifying 2A Main Body ECU Connector Terminals
      G05391138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Reconnect the front door courtesy light switch connector.
    5. Reconnect the main body ECU connector.

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : REPLACE MAIN BODY ECU  (See REMOVAL ).

  11. READ VALUE OF INTELLIGENT TESTER OR TECHSTREAM (FRONT DOOR COURTESY SWITCH (DRIVER SIDE)) 
    1. Connect an intelligent tester or a Techstream to the DLC3.
    2. Turn the ignition switch on (IG) and turn the tester on.
    3. Operate the intelligent tester or Techstream according to the display and select "DATA LIST" or "Data List" (See DATA LIST / ACTIVE TEST  ).
      1. Intelligent tester

        Body / Main Body / Data List: 

        BODY / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        D DOR CTY SW Driver side door courtesy light switch signal ON or OFF ON: Driver side door is open
        OFF: Driver side door is closed        		 -
      2. Techstream

        Body Electrical / Main Body / Data List: 

        BODY ELECTRICAL / MAIN BODY / DATA LIST

        Item Measurement Item / Range Normal Condition Diagnostic Note
        D Door Courtesy SW Driver side door courtesy light switch signal ON or OFF ON: Driver side door is open
        OFF: Driver side door is closed        		 -

    NG: Go to step 12 

    OK : REPLACE COMBINATION METER ASSEMBLY  (See REMOVAL  ).

  12. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE) 
    1. Disconnect the H1 front door courtesy light switch LH connector.
    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Switch Condition Specified Condition
      H1-1 - Body ground Not pushed (ON) Below 1 Ω
      H1-1 - Body ground Pushed (OFF) 10 kΩ or higher
      Fig 5: Identifying Door Courtesy Light Switch
      G04833360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Reconnect the front door courtesy light switch LH connector

    NG : REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)  (See REMOVAL ).

    OK: Go to next step 

  13. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU) 
    1. Disconnect the H1 front door courtesy light switch connector.
    2. Disconnect the 2A main body ECU connector.
    3. Measure the resistance according to the value in the table below.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      H1-1 - 2A-21 (DCTY) Always Below 1 Ω
      Fig 6: Checking Harness And Connector (Front door Courtesy Light Switch - Main Body ECU)
      G05391138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Reconnect the front door courtesy light switch connector.
    5. Reconnect the main body ECU connector.

    NG : REPLACE FRONT DOOR COURTESY LIGHT SWITCH (DRIVER SIDE)  (See REMOVAL ).

    OK : REPLACE MAIN BODY ECU  (See REMOVAL ).

scientia non olet · About LEMON Manuals