LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2005 >> tC Automatic >> Repair and Diagnosis >> Body & Frame >> Seats >> Seat >> Rear Seat >> Overhaul

Rear Seat: Overhaul

HINT:

CAUTION: Wear protective gloves. Sharp areas on the seatback frame can cause injuries to your hands.
  1. REMOVE TONNEAU COVER ASSY 
  2. REMOVE DECK BOARD SUB-ASSY 
  3. REMOVE REAR SEAT CUSHION ASSY 
    1. Pull up the 2 front portions of the seat cushion.
      NOTE: The cushion frame deforms easily. To avoid deforming the seat cushion, place your hands near the hook as shown in Fig 1 , and then pull the seat cushion upward. Repeat for the other hook.
      Fig 1: Removing Rear Seat Cushion
      G03073188Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the inner belts through the slits on the seat cushion.
    3. Remove the 2 seat cushion hooks from the seatback frame. Then remove the seat cushion.
    Fig 2: Removing Seat Cushion Hooks
    G03073189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE DECK BOARD NO. 1 (See  REPLACEMENT  ) 
  5. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER 
    1. Detach the 12 claws and remove the 3 anchor covers as shown in Fig 3 .
    Fig 3: Removing Anchor Covers
    G03073190Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET 
    1. Remove the 3 bolts and 3 anchor brackets.
  7. REMOVE REAR FLOOR BOARD NO. 1 (See  REPLACEMENT  ) 
  8. REMOVE REAR SEATBACK ASSY LH 
    1. Fully fold the seatback forward.
    2. Remove the 2 bolts on the rear side of the seatback.
    3. Return the seatback to the upright position.
    4. Remove the 2 bolts on the front side of the seatback. Then remove the seatback.
    NOTE: Be careful not to damage the vehicle body.
    Fig 4: Removing 2 Bolts On Front Side Of Seatback
    G03073191Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE REAR SEATBACK ASSY RH 
    1. Remove the bolt and rear seat 3-point type belt floor anchor.
    2. Fully fold the seatback forward.
    3. Remove the 2 bolts on the rear side of the seatback.
    4. Return the seatback to the upright position.
    5. Remove the 2 bolts on the front side of the seatback.

      Then remove the seatback.

    NOTE: Be careful not to damage the vehicle body.
    Fig 5: Removing 2 Bolts On Front Side Of Seatback
    G03073192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE REAR SEAT HEADREST ASSY LH 
  11. REMOVE REAR SEAT HEADREST ASSY RH 
  12. REMOVE REAR SEAT HEADREST ASSY CENTER 
  13. REMOVE REAR SEAT CUSHION LOCK HOOK 
    1. Using a screwdriver, detach the claws and remove the 2 lock hooks.

    HINT:

    Tape the screwdriver tip before use.

  14. REMOVE NO. 3 SEAT LEG SUB-ASSY 
    1. Using a clip remover, remove the 2 clips.
    2. Partially remove the floor carpet, and remove the 4 bolts and seat leg.
  15. REMOVE REAR SEAT CUSHION COVER 
    1. Remove the hog rings and seat cushion cover from the seat cushion pad.
  16. REMOVE REAR SEAT RECLINING COVER NO. 2 LH 
    1. Remove the clip and reclining cover in the direction indicated by the arrow shown in Fig 6 .
    Fig 6: Removing Clip And Reclining Cover
    G03073193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE REAR SEAT RECLINING COVER LH 

    HINT:

    Use the same procedures described for the reclining cover No. 2 LH.

  18. REMOVE REAR SEAT RECLINING COVER NO. 2 RH 

    HINT:

    Use the same procedures described for the LH side.

  19. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSY LH 
    1. Using a screwdriver, detach the 2 claws and remove the rear seatback lock striker cover.

      HINT:

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.
      Fig 7: Removing Rear Seat Screw
      G03073194Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 reclining control cables as shown in Fig 8 . Then remove the control lever.
    Fig 8: Removing Reclining Control Cables
    G03073195Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. REMOVE REAR SEATBACK COVER LH 
    1. Remove the hog rings. Open the lower part of the seat-back cover.
    2. Open the zipper.
      Fig 9: Identifying Zipper Area
      G03073196Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pull the seatback board in the direction indicated by the arrow shown in Fig 10 to detach the 2 claws labeled A.
    4. Pull the seatback board in the direction indicated by the arrow shown in Fig 10 to detach the 2 hooks labeled B. Then, remove the seatback board.
      Fig 10: Pulling Seatback Board
      G03073197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Detach the 4 claws and remove the 2 headrest supports.
    6. Remove the seatback cover (with pad) from the seatback frame.
    7. Remove the hog rings and seatback cover from the seat-back pad.
    Fig 11: Removing 2 Headrest Supports
    G03073198Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  21. REMOVE REAR SEAT RECLINING CONTROL CABLE LH 
    1. Remove the 2 control cables as shown in Fig 12 .
    Fig 12: Removing Rear Seat Reclining Control Cable
    G03073199Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSY RH 

    HINT:

    Use the same procedures described for the LH side.

  23. REMOVE REAR SEAT SHOULDER BELT GUIDE CENTER 
    1. Using a screwdriver, detach the 2 claws labeled A.

      HINT:

      Tape the screwdriver tip before use.

    2. Pull the inside cover in the direction indicated by the arrow shown in Fig 13 to detach the claw. Then, remove the bracket cover.
    Fig 13: Removing Claws
    G03073200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  24. REMOVE REAR SEATBACK COVER RH 
    1. Remove the hog rings. Open the lower part of the seat-back cover.
    2. Open the zipper.
      Fig 14: Identifying Zipper Area
      G03073201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pull the seatback board in the direction indicated by the arrow shown in Fig 15 to detach the 2 claws labeled A.
    4. Pull the seatback board in the direction indicated by the arrow shown in Fig 15 to detach the 3 hooks labeled B.

      Then remove the seatback board.

      Fig 15: Identifying Seatback Board
      G03073202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Detach the 8 claws and remove the 4 headrest supports.
    6. Remove the seatback cover (with pad) from the seatback frame.
    7. Remove the hog rings and seatback cover from the seat-back pad.
    Fig 16: Removing 4 Headrest Supports
    G03073203Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  25. REMOVE REAR SEAT SIDE HINGE MALE COVER RH 
    1. Remove the 2 screws.
    2. Using a screwdriver, detach the 2 claws and remove the male cover.

    HINT:

    Tape the screwdriver tip before use.

    Fig 17: Removing Rear Seat Side Hinge Male Cover RH
    G03073204Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. REMOVE REAR SEAT SIDE HINGE MALE COVER LH 
    1. Remove the male cover in the direction indicated by the arrow shown in Fig 18 .
    Fig 18: Removing Male Cover
    G03073205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE REAR SEAT SIDE HINGE MALE COVER 
    1. Using a screwdriver, detach the claws and remove the male cover.

    HINT:

    Tape the screwdriver tip before use.

  28. REMOVE REAR SEAT 3-POINT TYPE BELT ASSY RH 
    1. Detach the 2 claws and open the shoulder belt cover.
      Fig 19: Opening Shoulder Belt Cover
      G03073206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the hook.
    3. Remove the 4 nuts and belt.
    Fig 20: Detaching Hook
    G03073207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  29. REMOVE REAR SEAT SHOULDER BELT COVER RH 
    1. Detach the 3 claws and remove the belt cover.
    Fig 21: Removing Belt Cover
    G03073208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  30. REMOVE REAR SEAT RECLINING CONTROL CABLE RH 

    HINT:

    Use the same procedures described for the LH side.

  31. INSTALL REAR SEAT 3-POINT TYPE BELT ASSY RH 
    1. Install the belt with the nut as shown in Fig 22 .
      1. Torque: 42 N.m (428 kgf.cm, 31 ft.lbf) 
    2. Attach the hook.
      Fig 22: Installing Belt
      G03073209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Align the holes of the 3 parts in Fig 23 , and then install the 3 nuts.
    Fig 23: Aligning Holes
    G03073210Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    Before tightening the nuts, raise the seatback to the upright position and make sure the seatback stops in the first lock position of the frame.

    Fig 24: Raising Seatback
    G03073211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. INSTALL REAR SEATBACK COVER LH 
    NOTE:
    • Be careful not to damage the cover.
    • When installing the hog rings, take care to minimize wrinkles as much as possible.
    1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
    2. Install the seatback cover (with pad) to the seatback frame.
    3. Install the 2 headrest supports.
    4. Install the seatback board to the seatback frame.
    5. Close the zipper.
    6. Using hog ring pliers, install the seatback cover (with pad) with new hog rings.
    Fig 25: Installing Seatback Cover Using Hog Ring Pliers
    G03073212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. INSTALL REAR SEATBACK COVER RH 
    NOTE:
    • Be careful not to damage the cover.
    • When installing the hog rings, take care to minimize wrinkles as much as possible.
    1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
    2. Install the seatback cover (with pad) to the seatback frame.
    3. Install the 4 headrest supports.
    4. Install the seatback board to the seatback frame.
    5. Close the zipper.
    6. Using hog ring pliers, install the seatback cover (with pad) with new hog rings.
  34. INSTALL REAR SEAT CUSHION COVER 
    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
    NOTE:
    • Be careful not to damage the cover.
    • When installing the hog rings, take care to minimize wrinkles as much as possible.
  35. INSTALL NO. 3 SEAT LEG SUB-ASSY 
    1. Install the seat leg with the 4 bolts.
      1. Torque: 40 N.m (408 kgf.cm, 30 ft.lbf) 
  36. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET 
    1. Install the 3 brackets with the 3 bolts.
      1. Torque: 19.6 N.m (200 kgf.cm, 14 ft.lbf) 
  37. INSTALL REAR SEATBACK ASSY LH 
    1. Place the seat in the cabin.
      NOTE: Be careful not to damage the vehicle body.
    2. Tighten the 4 bolts in the order indicated in Fig 26 .
      1. Torque: 40 N.m (408 kgf.cm, 30 ft.lbf) 
    Fig 26: Installing Rear Seatback Assy LH
    G03073213Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  38. INSTALL REAR SEATBACK ASSY RH 
    1. Place the seat in the cabin.
      NOTE: Be careful not to damage the vehicle body.
    2. Tighten the 4 bolts in the order indicated in Fig 27 .
      1. Torque: 40 N.m (408 kgf.cm, 30 ft.lbf) 
    3. Install the rear seat 3-point type belt floor anchor with the bolt.
      1. Torque: 42 N.m (428 kgf.cm, 31 ft.lbf) 
    Fig 27: Installing Rear Seatback Assy RH
    G03073214Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  39. INSTALL REAR SEAT CUSHION ASSY 
    1. Attach the 2 seat cushion's rear hooks to the seatback frame.
    2. Insert the inner belts through the slits on the seat cushion.
      Fig 28: Installing Rear Seat Cushion Assy
      G03073215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Attach the 2 seat cushion's front hooks to the rear seat cushion lock hooks.

    HINT:

    Confirm that the seat cushion is firmly installed.

    Fig 29: Attaching Seat Cushion Front Hooks
    G03073216Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals