Cuts Out, Misses

WARNING: This page is about a different variant/trim than selected.

Cuts Out, Misses

Inspections	Action
DEFINITION: Steady pulsation or jerking that follows engine speed, usually more pronounced as engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or low speed.
Preliminary	Refer to Important Preliminary Inspections Before Beginning in Symptoms - Engine Controls . Search for bulletins. Verify that the engine control module (ECM) grounds are clean, tight, and in the proper locations. Refer to Power and Grounding Component Views in Wiring Systems and Engine Controls Schematics . Remove the air filter element and inspect for dirt and for restrictions. Refer to Air Cleaner Element Replacement . Replace as necessary.
Fuel Systems	Test the fuel injectors. Refer to Fuel Injector Coil Test . Test for incorrect fuel pressure. Refer to Fuel System Diagnosis . Inspect for a restricted fuel filter. Refer to Fuel System Diagnosis . Inspect for a contaminated fuel condition. Refer to Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) . Inspect for the following conditions that may cause the engine to run rich: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector Purging of a saturated EVAP canister Incorrect fuel pressure-Refer to Fuel System Diagnosis . A leaking fuel pressure regulator-Refer to Fuel System Diagnosis . Leaking fuel injectors-Refer to Fuel System Diagnosis . Proper operation of the MAP sensor-Refer to DTC P0106 . Vacuum hoses that are split, kinked, or improperly connected An air intake duct that is collapsed or restricted An air filter that is dirty or restricted-Refer to Air Cleaner Element Replacement . Inspect for the following conditions that may cause the engine to run lean: NOTE: Refer to Heated Oxygen and Oxygen Sensor Notice in Cautions and Notices. Water intrusion in the HO2S connector An exhaust leak between the HO2S and the engine-Refer to Exhaust Leakage in Engine Exhaust. Vacuum leaks Incorrect fuel pressure-Refer to Fuel System Diagnosis . Restricted fuel injectors-Refer to Fuel Injector Balance Test with Special Tool . Proper operation of the MAP sensor-Refer to DTC P0106 . Fuel contamination-Refer to Alcohol/Contaminants-in-Fuel Diagnosis (With Special Tool) or Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool) . Vacuum hoses that are split, kinked, or improperly connected
Sensor/System	Verify that the engine coolant temperature (ECT) sensor is not shifted in value. Refer to Temperature vs Resistance . Use a scan tool in order to monitor the knock sensor (KS) system for excessive spark retard activity. Refer to Scan Tool Data List . Inspect for throttle body tampering, excessive deposits, or damage. Inspect for a vacuum leak. Inspect the crankcase ventilation system for proper operation. Refer to Crankcase Ventilation System Inspection/Diagnosis in Engine Mechanical.
Ignition System	In order to properly inspect the spark plugs or to correct a condition, refer to the following procedures: Ignition System Specifications Spark Plug Inspection Spark Plug Replacement Inspect for proper secondary ignition voltage output with J 26792 (SA9199Z) Spark Tester. See Special Tools . An improper spark plug gap will cause a driveability condition. Gap the spark plugs using a wire gauge gap tool. If the spark plugs are found to be fouled, determine the cause before replacing the spark plugs. Inspect for damaged or misaligned spark plug boots. Inspect the electronic ignition (EI ) module for a proper ground connection. Monitor the Misfire Current Counters while driving the vehicle in the conditions that the symptom occurred. If a misfiring cylinder can be located, use the DTC P0300 table for diagnosis. Refer to DTC P0300 .
Engine Mechanical	Inspect engine mechanical for the following: Compression Sticking or leaking valves Worn camshaft lobes Valve timing Worn rocker arms Broken valve springs Excessive oil in combustion chamber or leaking valve seals. For more information, refer to one or more of the following procedures in Engine Mechanical: Engine Compression Test Symptoms - Engine Mechanical Oil Consumption Diagnosis For incorrect, worn, or damaged basic engine parts, inspect the following: The camshaft-Refer to Camshaft Cleaning and Inspection in Engine Mechanical. The cylinder heads-Refer to Cylinder Head Cleaning and Inspection in Engine Mechanical. The pistons, etc.-Refer to Piston, Connecting Rod, and Bearings Cleaning and Inspection in Engine Mechanical. Refer to Symptoms - Engine Mechanical in Engine Mechanical for diagnosis procedures.
Additional Inspections	Inspect the exhaust system for possible restrictions. Inspect for the following: Inspect the exhaust system for damaged or collapsed pipes. Inspect the mufflers for heat distress or possible internal failure. Inspect for possible plugged catalytic converters. Refer to Restricted Exhaust in Engine Exhaust. Electromagnetic interference (EMI) can cause an engine misfire condition. A sudden increase in indicated RPM parameter with little change in actual engine RPM change indicates EMI is present. Inspect for high voltage components near ignition control circuits if a condition exists. Inspect the intake manifold and the exhaust manifold passages for casting flash.