LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2017 >> Panamera Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (27 Starter, Power Supply, Cruise Control 4.0L Turbo Hybrid -- 971 - PANAMERA (971)) >> WM, 270819 Removing And Installing E-Box >> Remove E-Box

Remove E-Box

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 Porsche Panamera, 2022 Porsche Panamera, 2021 Porsche Panamera, 2020 Porsche Panamera, and 2019 Porsche Panamera. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Incorrect handling of high-voltage components 
  • Electric shock 
  • Short circuit 
  • Fire 
  • Explosion 

    → Only appropriately trained and authorized persons may work on high-voltage vehicles and components.

    → Required qualification: High voltage technician or high voltage expert.

    → Observe national requirements and legislation for this work.

    → Always use insulated tools, such as an > VAS 6883 - insulated tool set  when working on these parts.

    → Observe general warning notices for working on the high-voltage system.

    > 2X00IN GENERAL WARNING NOTICES FOR WORKING ON THE HIGH-VOLTAGE SYSTEM

  1. Perform tests for verifying absence of electric charge and insulation resistance tests using > VAS 6558A - High-voltage testing module  , > VAS 6558/9-7 - High-voltage test adapter HVR 40  and > 9900 - PIWIS Tester 3  .

    > 270803 PERFORMING MEASUREMENTS ON THE HIGH-VOLTAGE BATTERY 

  2. Loosen retaining frame at the top -2-  .
    1. 2.1 Unscrew fastening screws -1-  .
      G15879808Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Fastening screws on retaining frame

    2. 2.2 Unscrew fastening screws -3 and 4-  .
    G15879809Courtesy of PORSCHE CARS NORTH AMERICA, INC.

    Fastening screws on retaining frame

  3. Remove pressure accumulator with load distributor plate and retaining frame.
    1. 3.1 Unscrew fastening screws -5-  .
      G15879810Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Fastening screws on pressure accumulator, bottom

    2. 3.2 Unscrew fastening screws -6-  .
      G15879811Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Fastening screws on retaining frame, bottom

    3. 3.3 Remove load distributor plate together with lower bar from the high-voltage battery and set it aside.
    4. 3.4 Remove retaining frame together with the pressure accumulator from the high-voltage battery and set it aside.
  4. Remove E-box.
    1. 4.1 Unscrew fastening screws -1-  using > VAS 691 003A - High-voltage tool set TORX®  . The exposed threads must be cleaned.

      Replace micro-self-locking screws.

      G15879812Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Fastening screws on E-box

    2. 4.2 > 9924 - Centring pins-3-  must now be screwed into the free bores.
      G15879813Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Centring pins on E-box

    3. 4.3 Unscrew and remove fastening screw -4-  .

      Replace micro-self-locking screw.

      G15879814Courtesy of PORSCHE CARS NORTH AMERICA, INC.

      Loosening E-box

    4. 4.4 Carefully disconnect E-box from the high-voltage battery.
scientia non olet · About LEMON Manuals