LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 137 (53 - Body Rear - CARRERA (997)) >> WM 536155 Replacing Inner Side Section (Except CABRIO Models) >> Removing Inner Side Section >> Removing Inner Side Section (Upper Part)

Removing Inner Side Section (Upper Part)

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Identifying Installation Position Of Inner Side Section (Upper Part)
G09823468Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Remove rear center panel reinforcement. → 512155 REPLACING REAR CENTRE PANEL REINFORCEMENT - section on "Removing"
  2. Replace roof pillar (pipe). → 510555 REPLACING ROOF PILLAR (PIPE) - section on "Removing"
  3. Milling off spotwelds
    1. 3.1. Mill off spotwelds in areas -A, B, C, E-  using a spotweld cutter.
    2. 3.2. Mill off spotwelds in area -D-  using a spotweld cutter (2 plate thicknesses).
      Fig 2: Identifying Milling Off Spotwelds Areas D Using Spotweld Cutter (2 Plate Thicknesses)
      G09823469Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Milling off spotwelds
    1. 4.1. Mill off spotwelds in areas -A-  and -B-  using a spotweld cutter.
      Fig 3: Identifying Milling Off Spotwelds A And B Using Spotweld Cutter
      G09823470Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Separating inert-gas welded seam
    1. 5.1. Separate inert-gas welded seam in area -A-  from the inside using a parting grinder.
      Fig 4: Separating Inert-Gas Welded Seam
      G09823471Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Milling off spotwelds
    1. 6.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 5: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823472Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  7. Milling off spotwelds
    1. 7.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 6: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823473Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  8. Milling off spotwelds
    1. 8.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 7: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823474Courtesy of PORSCHE CARS NORTH AMERICA, INC.


Fig 1: Identifying Installation Position Of Inner Side Section (Upper Part)
G09823516Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  1. Remove rear center panel reinforcement. → 512155 REPLACING REAR CENTRE PANEL REINFORCEMENT - section on "Removing"
  2. Replace roof pillar (pipe). → 510555 REPLACING ROOF PILLAR (PIPE) - section on "Removing"
  3. Milling off spotwelds
    1. 3.1. Mill off spotwelds in areas -A, B, C, E-  using a spotweld cutter.
    2. 3.2. Mill off spotwelds in area -D-  using a spotweld cutter (2 plate thicknesses).
      Fig 2: Identifying Milling Off Spotwelds Area D Using Spotweld Cutter (2 Plate Thicknesses)
      G09823517Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Milling off spotwelds
    1. 4.1. Mill off spotwelds in areas -A-  and -B-  using a spotweld cutter.
      Fig 3: Identifying Milling Off Spotwelds Area A And B Using Spotweld Cutter
      G09823518Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Separating inert-gas welded seam
    1. 5.1. Separate inert-gas welded seam in area -A-  from the inside using a parting grinder.
      Fig 4: Separating Inert-Gas Welded Seam
      G09823519Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Milling off spotwelds
    1. 6.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 5: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823520Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  7. Milling off spotwelds
    1. 7.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 6: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823521Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  8. Milling off spotwelds
    1. 8.1. Mill off spotwelds in area -A-  using a spotweld cutter.
      Fig 7: Identifying Milling Off Spotwelds Area A Using Spotweld Cutter
      G09823522Courtesy of PORSCHE CARS NORTH AMERICA, INC.
scientia non olet · About LEMON Manuals