LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2016 >> 911 Turbo, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 137 (53 - Body Rear - CARRERA (997)) >> WM 536155 Replacing Inner Side Section (Except CABRIO Models) >> Installing Inner Side Section >> Installing Inner Side Section (Upper Part)

Installing Inner Side Section (Upper Part)

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2013 Porsche 911, 2012 Porsche 911, 2011 Porsche 911, 2010 Porsche 911, and 2009 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.
  1. Fitting top inner side section to the body
    1. 1.1. Fit the top inner side section to the body and fix in place with tensioning clamps.
  2. Welding in top inner side section
    1. 2.1. Resistance spot-weld the top inner side section in areas -A-  and -C-  .
    2. 2.2. Plug-weld the top inner side section in areas -B-  and -D-  using inert gas.
      Fig 1: Identifying Welding In Top Inner Side Section
      G09823487Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  3. Welding in top inner side section
    1. 3.1. Resistance spot-weld the top inner side section in area -A-  .
      Fig 2: Identifying Welding In Top Inner Side Section
      G09823488Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Welding in top inner side section
    1. 4.1. Resistance spot-weld the top inner side section in area -A-  .
      Fig 3: Identifying Welding In Top Inner Side Section
      G09823489Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Welding in top inner side section
    1. 5.1. Apply a full weld to the top inner side section in area -A-  using inert gas.
      Fig 4: Identifying Welding In Top Inner Side Section
      G09823490Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Fitting reinforcement for seat belt height adjustment to the body
    1. 6.1. Fit reinforcement for seat belt height adjustment to the body and fix in place with tensioning clamps.
  7. Welding in reinforcement for seat belt height adjustment
    1. 7.1. Resistance spot-weld reinforcement for seat belt height adjustment in areas -A, B, C, D-  .
      Fig 5: Welding In Reinforcement For Seat Belt Height Adjustment
      G09823491Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  8. Fitting front inner side section to the body
    1. 8.1. Fit the front inner side section to the body and fix in place with tensioning clamps.
  9. Welding in front inner side section
    1. 9.1. Resistance spot-weld the front inner side section in areas -A, B, C, D-  .
      Fig 6: Identifying Welding In Front Inner Side Section
      G09823492Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Install roof pillar (pipe). → 510555 REPLACING ROOF PILLAR (PIPE) - section on "Installing"
  11. Install rear center panel reinforcement. → 512155 REPLACING REAR CENTRE PANEL REINFORCEMENT - section on "Installing"


  1. Fitting top inner side section to the body
    1. 1.1. Fit the top inner side section to the body and fix in place with tensioning clamps.
  2. Welding in top inner side section
    1. 2.1. Resistance spot-weld the top inner side section in areas -A-  and -C-  .
    2. 2.2. Plug-weld the top inner side section in areas -B-  and -D-  using inert gas.
      Fig 1: Identifying Welding In Top Inner Side Section
      G09823535Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  3. Welding in top inner side section
    1. 3.1. Resistance spot-weld the top inner side section in area -A-  .
      Fig 2: Identifying Welding In Top Inner Side Section
      G09823536Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  4. Welding in top inner side section
    1. 4.1. Resistance spot-weld the top inner side section in area -A-  .
      Fig 3: Identifying Welding In Top Inner Side Section
      G09823537Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  5. Welding in top inner side section
    1. 5.1. Apply a full weld to the top inner side section in area -A-  using inert gas.
      Fig 4: Identifying Welding In Top Inner Side Section
      G09823538Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  6. Fitting reinforcement for seat belt height adjustment to the body
    1. 6.1. Fit reinforcement for seat belt height adjustment to the body and fix in place with tensioning clamps.
  7. Welding in reinforcement for seat belt height adjustment
    1. 7.1. Resistance spot-weld reinforcement for seat belt height adjustment in areas -A, B, C, D-  .
      Fig 5: Identifying Welding In Reinforcement For Seat Belt Height Adjustment
      G09823539Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  8. Fitting front inner side section to the body
    1. 8.1. Fit the front inner side section to the body and fix in place with tensioning clamps.
  9. Welding in front inner side section
    1. 9.1. Resistance spot-weld the front inner side section in areas -A, B, C, D-  .
      Fig 6: Identifying Welding In Front Inner Side Section
      G09823540Courtesy of PORSCHE CARS NORTH AMERICA, INC.
  10. Install roof pillar (pipe). → 510555 REPLACING ROOF PILLAR (PIPE) - section on "Installing"
  11. Install rear center panel reinforcement. → 512155 REPLACING REAR CENTRE PANEL REINFORCEMENT - section on "Installing"
scientia non olet · About LEMON Manuals