Connector - General information

Information 

For repairing wire harnesses, the wire harnesses listed in step 1 are only offered as complete units, without exchanging individual connectors.

For repairing or replacing connectors on wire harnesses which do not have to be completely replaced, the correct procedure is listed under Step  2 and  3.

1. Wire harnesses which are replaced only as a complete unit. 
   1. 1.1. Wire harness for door and wire harness for door panel→ 973219 REMOVING AND INSTALLING WIRE HARNESS FOR DOOR 
   2. 1.2. Wire harness for center console→ 972019 REMOVING AND INSTALLING WIRE HARNESS FOR CENTRE CONSOLE 
   3. 1.3. Wire harness for number plate light→ 977019 REMOVING AND INSTALLING WIRE HARNESS FOR NUMBER PLATE LIGHT 
   4. 1.4. Wire harness for rear spoiler→ 976719 REMOVING AND INSTALLING WIRE HARNESS FOR REAR SPOILER 
   5. 1.5. Wire harness for glove compartment→ Removing And Installing Contact Switch For Glove Compartment Light
   6. 1.6. Wire harness for engine→ 975219 REMOVING AND INSTALLING WIRE HARNESS FOR ENGINE 
   7. 1.7. Wire harness for Tiptronic→ 978119 REMOVING AND INSTALLING WIRE HARNESS FOR TIPTRONIC 
   8. 1.8. Wire harness for battery wiring→ 974519 REMOVING AND INSTALLING WIRE HARNESS FOR STARTER BATTERY 
   9. 1.9. Antenna lines → Replacing Antenna Lines

      Information 

      Only in the cabrio.

   10. 1.10. Wire harness for roll-over protection system→ 975519 REMOVING AND INSTALLING WIRE HARNESS FOR CONVERTIBLE TOP 

       Information 

       Only in the cabrio.

   11. 1.11. Wire harness for additional brake light. → 970919 REMOVING AND INSTALLING MAIN WIRE HARNESS 
2. Connectors contained in the Repair Kit For Wire Harnesses Nr. 155-1 and can be replaced individually. 
   NOTE: Using plug-in contacts made of different materials

   • Oxidation of plug-in contacts

   → Only use the plug contacts listed in the wiring diagram for the corresponding plug connection. Always plug gold contacts together with gold contacts.

   → The wiring diagrams can be displayed using PIWIS Tester II 9818  .

   For repairing wire harnesses, individual connectors are offered in a Repair Kit For Wire Harnesses Nr. 155-1  . In this Repair Kit For Wire Harnesses Nr. 155-1  , connectors are contained primarily that are installed in crash and external areas.

   The Repair Kit For Wire Harnesses Nr. 155-1  contains detailed descriptions about removing and installing individual plug-in contacts.

3. Connectors not contained in the Repair Kit For Wire Harnesses Nr. 155-1. 

   Connectors not contained in the Repair Kit For Wire Harnesses Nr. 155-1  can be ordered from the CARTOOL company.

   Information 

   Ordering connectors refers to the model 911 Carrera as of model year 98  .

   The order must contain the following specifications.

   1. 3.1. Version 1 for identifying the required connector:
      1. 3.1.1. Legible specifications of the manufacturer on the connector, e.g., complete item number, number of pins, housing color, and whether pin or socket housing.
      2. 3.1.2. If the data mentioned in Version 1 is not legible, is incomplete, or not present, Version 2 is also possible for ordering.
   2. 3.2. Version 2 for identifying the required connector:
      1. 3.2.1. Vehicle type
      2. 3.2.2. Model year
      3. 3.2.3. PORSCHE part number from the parts catalogue
      4. 3.2.4. Which wire harness (e.g. main wire harness, wire harness for engine, etc.)
      5. 3.2.5. Specifications from the wiring diagram
         1. Page number
         2. Field
         3. Component (for components with multiple connectors e.g. instrument cluster, please specify connector 1, 2, 3 etc.)
         4. Connection point (e.g. X11, X12 etc.)
   3. 3.3. Version 3 for identifying the required connector:
      1. 3.3.1. Call up corresponding wiring diagram in PIWIS tester 9718  .
      2. 3.3.2. Click on the plug-in contact of the required connector with the mouse.

         Information 

         The specifications displayed are subject to a constant updating process. For this reason, it can happen that specifications are incomplete or not available. If this is the case, use one of the other versions for ordering connectors if possible.

      3. 3.3.3. Note all displayed specifications for this connector and specify when ordering the connector.
   4. 3.4. If the data listed under Version 1 to Version 3 is included and complete, the CARTOOL company can identify the correct connector.
   5. 3.5. Ordering address:

      CARTOOL company, GmbH 

      Strausenlettenstr. 15

      85053 Ingolstadt

      Tel. (0841) 96 500-70 (in Germany)

      Tel. (0841) 96 500-80 (outside of Germany)

      Fax (0841) 96 500-90