LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2011 >> 911 Speedster >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (Radio, Navigation & Pcm Diagnosis - 911 CARRERA (996)) >> PCM2 MMI control module function >> Input signals

Input signals

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2005 Porsche 911, 2004 Porsche 911, 2003 Porsche 911, 2002 Porsche 911, and 2001 Porsche 911. However, it is still accessible from the selected car via links, so may be relevant.

The following queries can be run using this menu item:

NOTE: Deactivate the automatic traffic announcement before performing the diagnosis on the PCM2. If this is not done, the diagnosis will abort (only for software version < 03).
INPUT SIGNALS

Menu item Function
  • Key code
 Under this menu item, it is possible to check that the operating buttons are functioning during troubleshooting.
  • Connect and start the Porsche System Tester II 9588 and switch on the ignition.
  • Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key.
  • Select PCM in the Control modules menu and confirm with the "FORWORD" key.
  • Select PCM2 MMI in the PCM2 function selection and confirm with the "FORWORD" key.
  • Select the Input signals menu item and confirm with the "FORWORD" key.
  • Key code is displayed on the Porsche System Tester II 9588. The function is activated by marking with the ">" key and actuating the "FORWORD" key.
  • If functioning correctly, the relevant code appears on the tester's display field when the operating buttons are activated.
  • Increment steps
 This menu item shows the current status of the operating button.
  • Connect and start the Porsche System Tester II 9588 and switch on the ignition.
  • Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key.
  • Select PCM in the Control modules menu and confirm with the "FORWORD" key.
  • Select PCM2 MMI in the PCM2 function selection and confirm with the "FORWORD" key.
  • Select the Input signals menu item and confirm with the "FORWORD" key.
  • Select the Input signals menu item and confirm with the "FORWORD" key.
  • Increment steps is displayed on the Porsche System Tester II 9588. The function is activated by marking with the ">" key and actuating the "FORWORD" key.
  • If functioning correctly, the relevant code appears on the tester's display field when the operating buttons are activated.


The following queries can be run using this menu item:

NOTE: Deactivate the automatic traffic announcement before performing the diagnosis on the PCM2. If this is not done, the diagnosis will abort.
INPUT SIGNALS

Menu item Function
  • Key code
 Under this menu item, it is possible to check that the operating buttons are functioning during troubleshooting.
  • Connect and start the Porsche System Tester II 9588 and switch on the ignition.
  • Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key.
  • Select PCM in the Control modules menu and confirm with the "FORWORD" key.
  • Select PCM2 MMI in the 911 (996) PCM2 function selection and confirm with the "FORWORD" key.
  • Select Input signals in the 911 (996) PCM2 MMI function selection and confirm with the "FORWORD" key.
  • Key code is displayed on the Porsche System Tester II 9588. The function is activated by marking with the ">" key and actuating the "FORWORD" key.
  • If functioning correctly, the relevant code appears on the tester's display field when the operating buttons are activated.
  • Increment steps
 This menu item shows the current status of the operating button.
  • Connect and start the Porsche System Tester II 9588 and switch on the ignition.
  • Select 911 (996) in the Vehicle type menu and confirm with the "FORWORD" key.
  • Select PCM in the Control modules menu and confirm with the "FORWORD" key.
  • Select PCM2 MMI in the 911 (996) PCM2 function selection and confirm with the "FORWORD" key.
  • Select Input signals in the 911 (996) PCM2 MMI function selection and confirm with the "FORWORD" key.
  • Increment steps is displayed on the Porsche System Tester II 9588. The function is activated by marking with the ">" key and actuating the "FORWORD" key.
  • If functioning correctly, the relevant code appears on the tester's display field when the operating buttons are activated.
scientia non olet · About LEMON Manuals