LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2006 >> Vibe Base, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 12 (Automatic Transmission - Mu4 - Overhaul) >> Repair Instructions >> Forward Clutch Assembly Installation

Forward Clutch Assembly Installation

WARNING: This page is about a different variant/trim than selected.

Tools Required

NOTE: When installing new clutch discs in the 1st-reverse brake, forward clutch or direct clutch assemblies, the new clutch discs MUST be soaked in Dexron® - III automatic transmission fluid GM P/N 12341643, or equivalent, two hours prior to installation. This causes the clutch material on the discs to permeate with fluid which will aid in ease of assembly and prevent clutch overheating on first time engagement.
    Fig 1: Locating Forward Clutch Piston Seals
    GM165028Courtesy of GENERAL MOTORS CORP.
  1. Install the new forward clutch piston seals (1) onto the forward clutch piston (2).
  2. Apply J 36850  to the new forward clutch piston seals.
    3. Fig 2: View Of Forward Clutch Piston With Cup Side Facing Up
    GM165029Courtesy of GENERAL MOTORS CORP.
  3. Install the forward clutch piston (1) into the forward clutch drum (2) with the cup side facing upwards.
  4. Install the forward clutch piston return spring onto the forward clutch piston.
    5. Fig 3: Identifying J 23327
    GM165030Courtesy of GENERAL MOTORS CORP.
  5. Use J 23327  and a hydraulic press to install the forward clutch piston return spring snap ring (2) onto the forward clutch piston return spring retainer.
    6. Fig 4: Four Forward Clutch Discs, Plates & Forward Clutch Flange
    GM165041Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: The forward clutch flange must be installed with the flat side facing down and the stepped portion facing upwards.
  6. Install the four forward clutch discs (2), the four forward clutch plates (3) and the forward clutch flange (1) into the forward clutch drum in the following order:
    • One forward clutch plate
    • One forward clutch disc
    • One forward clutch plate
    • One forward clutch disc
    • One forward clutch plate
    • One forward clutch disc
    • One forward clutch plate
    • One forward clutch disc
    • The forward clutch flange
  7. Install the forward clutch snap ring into the direct clutch drum.
  8. Install three new input shaft seal rings onto the input shaft.
  9. Apply J 36850  to the new input shaft seal rings.
    10. Fig 5: Installing & Removing J 7872 On Forward Clutch Piston
    GM164982Courtesy of GENERAL MOTORS CORP.
  10. Use the J 7872  to measure the forward clutch piston stroke after completing assembly. See Special Tools .
    1. Place the J 7872  plunger on the on the forward clutch piston and apply 392-785 kPa (57-114 psi) of compressed air into the forward clutch apply passage (1) on the input shaft (2) and observe the J 7872  . See Special Tools .
    2. The standard forward clutch piston stroke should fall within 1.420-1.810 mm (0.0559-0.0713 in).
    3. If the forward clutch piston stroke is greater or less than specified, and all forward clutch components exhibit little or no wear, select one of the following different forward clutch flange sizes to bring the forward clutch piston stroke within specification:
      • 2.80 mm (0.110 in)
      • 3.00 mm (0.118 in)
      • 3.20 mm (0.126 in)
      • 3.370 mm (0.1327 in)
      • 3.600 mm (0.1417 in)
scientia non olet · About LEMON Manuals