Courtesy Lamps Always On

Step	Action	Yes	No
Schematic Reference: Interior Lights Schematics Connector End View Reference: Master Electrical Component List in Wiring Systems DEFINITION: The instrument panel (I/P) courtesy dome and roof rail courtesy lamps are ON at all times.
1	Did you perform the Diagnostic System Check - Vehicle?	Go to Step 2	Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2	Ensure the instrument panel (I/P) dimmer switch is not in the DOME position. Close all of the vehicle doors. Wait 20 seconds. Are the courtesy lamps illuminated?	Go to Step 3	Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
3	Use the scan tool in order to command the courtesy lamps OFF. Do the courtesy lamps turn OFF?	Go to Step 4	Go to Step 6
4	Close all of the vehicle doors. With a scan tool, observe the Driver Door Open Sw. parameter and the Passenger Door Open Sw. parameter in the Lamp Status data list. Does the scan tool indicate that both parameters are OFF?	Go to Step 14	Go to Step 5
5	Does the scan tool indicate that the Driver Door Open Sw. parameter is ON?	Go to Step 9	Go to Step 10
6	Disconnect the I/P dimmer switch. Are the courtesy lamps illuminated?	Go to Step 7	Go to Step 13
7	Test for a short to ground in the courtesy lamp switch ON signal circuit of the body control module (BCM). Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 8
8	Disconnect the BCM connector C1. Test the courtesy lamp supply voltage circuit for a short to battery positive voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 14
9	Disconnect the driver door lock switch. Observe the Driver Door Open Sw. parameter as you disconnect the switch. Does the scan tool indicate that the Driver Door Open Sw. parameter is OFF when the driver door lock switch is disconnected?	Go to Step 16	Go to Step 11
10	Disconnect the passenger door lock switches one at a time. Observe the Passenger Door Open Sw. parameter as you disconnect each switch. Does the scan tool indicate that the Passenger Door Open Sw. parameter is OFF when one of the passenger door lock switches is disconnected?	Go to Step 16	Go to Step 12
11	Test the driver door open switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 14
12	Test the passenger door open switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 14
13	Inspect for poor connections at the harness connector of the I/P dimmer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 15
14	Inspect for poor connections at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition?	Go to Step 18	Go to Step 17
15	Replace the I/P dimmer switch. Refer to Instrument Panel (I/P) Dimmer Switch Replacement . Did you complete the replacement?	Go to Step 18	-
16	Replace the inoperative door lock switch. Refer to Lock Replacement - Front Door or to Lock Replacement - Rear Door in Doors. Did you complete the replacement?	Go to Step 18	-
17	Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement?	Go to Step 18	-
18	Operate the system in order to verify the repair. Did you correct the condition?	System OK	Go to Step 2