Diagnosis Procedure
- CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY
- Turn ignition switch OFF.
- Disconnect intake valve timing (IVT) control solenoid valve harness connector.
- Turn ignition switch ON.
- Check the voltage between intake valve timing control solenoid valve harness connector and ground with CONSULT or tester.
DTC
+
-
Voltage
IVT control solenoid valve
Bank
Connector
Terminal
P0075
1
F67
1
Ground
Battery voltage
P0081
2
F66
1
Is the inspection result normal?
YES
GO TO 2.
NO
Repair open circuit, short to ground or short to power in harness or connectors.
- CHECK IVT CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
- Turn ignition switch OFF.
- Disconnect IPDM E/R harness connector.
- Check the continuity between IVT control solenoid valve harness connector and IPDM E/R harness connector.
DTC
IVT control solenoid valve
IPDM E/R
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0075
1
F67
1
F50
59
Existed
P0081
2
F66
1
- Also check harness for short to ground.
Is the inspection result normal?
YES
GO TO 3.
NO
Repair or replace error-detected parts.
- CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check the continuity between intake valve timing control solenoid valve harness connector and ECM harness connector.
DTC
IVT control solenoid valve
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0075
1
F67
2
F14
117
Existed
P0081
2
F66
2
119
- Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
GO TO 4.
NO
Repair open circuit, short to ground or short to power in harness or connectors.
- CHECK IVT CONTROL SOLENOID VALVE
Check the IVT control solenoid valve. Refer to Component Inspection (IVT Control Solenoid Valve) .
Is the inspection result normal?
YES
GO TO 5.
NO
Replace IVT control solenoid valve. Refer to Exploded View .
- CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE POWER SUPPLY
- Disconnect IVT intermediate lock control solenoid valve harness connector.
- Turn ignition switch ON.
- Check the voltage between IVT intermediate lock control solenoid valve harness connector and ground.
DTC
+
-
Voltage
IVT intermediate lock control solenoid valve
Bank
Connector
Terminal
P0075
1
F76
1
Ground
Battery voltage
P0081
2
F77
1
Is the inspection result normal?
YES
GO TO 7.
NO
GO TO 6.
- CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
- Turn ignition switch OFF.
- Disconnect IPDM E/R harness connector.
- Check the continuity between IVT intermediate lock control solenoid valve harness connector and IPDM E/R harness connector.
DTC
IVT intermediate lock control solenoid valve
IPDM E/R
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0075
1
F76
1
F50
59
Existed
P0081
2
F77
1
- Also check harness for short to ground.
Is the inspection result normal?
YES
Perform the trouble diagnosis for power supply circuit.
NO
Repair or replace error-detected parts.
- CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE GROUND CIRCUIT
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check the continuity between IVT intermediate lock control solenoid valve harness connector and ECM harness connector.
DTC
IVT intermediate lock control solenoid valve
ECM
Continuity
Bank
Connector
Terminal
Connector
Terminal
P0075
1
F76
2
F14
118
Existed
P0081
2
F77
2
120
- Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
GO TO 8.
NO
Repair or replace error-detected parts.
- CHECK IVT INTERMEDIATE LOCK CONTROL SOLENOID VALVE
Check the IVT intermediate lock control solenoid valve. Refer to Component Inspection (IVT Intermediate Lock Control Solenoid Valve) .
Is the inspection result normal?
YES
INSPECTION END
NO
Replace IVT intermediate lock control solenoid valve. Refer to Exploded View .