LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2016 >> Rogue S, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Exterior Lights >> Exterior Lighting System (Led Headlamp) >> Symptom Diagnosis >> Exterior Lighting System Symptoms >> Symptom Table

Symptom Table

CAUTION:

Perform the "Self Diagnostic Result" with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any DTC is detected.

Symptom Possible cause Inspection item
Headlamp (HI) is not turned ON. One side
  • Fuse
  • LED
  • Harness between IPDM E/R and headlamp (HI)
  • Harness between headlamp (HI) and ground
  • IPDM E/R
Headlamp (HI) circuit
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).
Both sides Symptom diagnosis 
"BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON"
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
  • Combination meter

    "Data Monitor""HI-BEAM IND"

  • BCM (HEAD LAMP)

    "Active Test""HEADLAMP"

Headlamp (LO) is not turned ON. One side
  • Fuse
  • LED
  • Harness between IPDM E/R and headlamp lamp (LO)
  • Harness between headlamp (LO) and ground
  • IPDM E/R
Headlamp (LO) circuit
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).
Both sides Symptom diagnosis 
"BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON"
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).
Each lamp is not turned ON/OFF with lighting switch AUTO.
  • Combination switch
  • Harness between combination switch and BCM
  • BCM
Combination switch
Refer to SYMPTOM TABLE (with Intelligent Key system) or SYMPTOM TABLE (without Intelligent Key system).
  • Optical sensor
  • Harness between optical sensor and BCM
  • BCM
Optical sensor
Refer to COMPONENT FUNCTION CHECK .
Daytime running light is not turned ON.
[Headlamp (HI) is turned ON.]
  • Fuse
  • Harness between IPDM E/R and front combination lamp
  • IPDM E/R
  • BCM
  • ECM
  • Combination meter
  • Daytime running light circuit

    Refer to DTC LOGIC .

  • BCM (HEADLAMP)

    "Data Monitor""ENGINE STATE"

  • Combination meter

    "Data Monitor""PKB SW"

  • BCM (HEADLAMP)

    "Active Test""DAYTIME RUNNING LIGHT"

Parking lamp is not turned ON.
  • Fuse
  • Parking lamp bulb
  • Harness between IPDM E/R and front combination lamp
  • IPDM E/R
Parking lamp circuit
Refer to DTC LOGIC .
Front side marker lamp is not turned ON.
  • Front side marker lamp bulb
  • Harness between IPDM E/R and front side marker lamp
  • Harness between front side marker lamp and ground
  • IPDM E/R
Front side marker lamp circuit
Refer to DTC LOGIC .
License plate lamp is not turned ON.
  • License plate lamp bulb
  • Harness between IPDM E/R and license plate lamp
  • Harness between license plate lamp and ground
License plate lamp circuit
Refer to DTC LOGIC .
Parking lamp, side marker lamp, tail lamp and license plate lamp are not turned ON. Symptom diagnosis 
"PARKING, SIDE MARKER, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON"
Refer to DESCRIPTION .
Tail lamp indicator is not turned ON.
(Exterior lamps are turned ON.)
Combination meter
  • Combination meter

    "Data Monitor""LIGHT IND"

  • BCM (HEADLAMP)

    "Active Test""TAIL LAMP"

Turn signal lamp does not blink. Indicator lamp is normal.
(Applicable side performs high flasher activation.)
  • Turn signal lamp bulb
  • Door mirror
  • Harness between BCM and each turn signal lamp
  • Harness between each turn signal lamp and ground
Turn signal lamp circuit
Refer to COMPONENT FUNCTION CHECK .
Turn signal indicator lamp does not blink.
(Turn signal lamp is normal.)
One side Combination meter -
Both sides
(Always)
  • Turn signal indicator lamp signal
  • BCM
  • Combination meter
  • Combination meter

    "Data Monitor""TURN IND"

  • BCM (FLASHER)

    "Active Test""FLASHER"

Both sides
(Only when activating hazard warning lamp with ignition switch OFF)
  • Combination meter power supply and ground circuit
  • Combination meter
Combination meter
Power supply and ground circuit
Refer to DIAGNOSIS PROCEDURE .
  • Hazard warning lamp does not activate.
  • Hazard warning lamp continues activating.
(Turn signal is normal.)
  • Hazard switch
  • Harness between hazard switch and BCM
  • Harness between hazard switch and ground
  • BCM
Hazard switch circuit
Refer to COMPONENT FUNCTION CHECK .
Front fog lamp is not turned ON. One side
  • Front fog lamp bulb
  • Harness between IPDM E/R and front fog lamp
  • Harness between front fog lamp and ground
  • IPDM E/R
Front fog lamp circuit
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).
Both sides Symptom diagnosis 
"BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON"
Refer to DTC LOGIC (LH) or DTC LOGIC (RH).