LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2015 >> Versa Note SL >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission (Diagnostic Trouble Codes (DTCS) P0713-P285A, Symptom Tests And R & I) (CVT: Re0F11A) >> DTC/Circuit Diagnosis >> DTC P1586: G Sensor >> Diagnosis Procedure >> Diagnostic Test

Diagnostic Test

  1. CHECK G SENSOR SIGNAL

    G-20With CONSULT 

    1. Park the vehicle on a level surface.
    2. Turn ignition switch ON.
    3. Select "Data Monitor" in "TRANSMISSION".
    4. Select "G SEN SLOPE".
    5. Swing the vehicle and check if value varies between - 40.45% and 40.45%.
      Monitor item Condition Standard
      G SEN SLOPE Flat road 0%
      Uphill Positive value (Maximum 40.45%)
      Downhill Negative value (Minimum - 40.45%)

    Is the inspection result normal?

    YES 

    GO TO STEP 2  .

    NO 

    GO TO STEP 3  .

  2. G SENSOR CALIBRATION (PART 1)

    G-20With CONSULT 

    1. Select "Self Diagnostic Results" in "TRANSMISSION".
    2. Touch "Erase".

    Perform "G SENSOR CALIBRATION". Refer to WORK PROCEDURE .

  3. CHECK SENSOR POWER SUPPLY

    1. Turn ignition switch OFF.
    2. Disconnect G sensor connector.
    3. Turn ignition switch ON.
    4. Check voltage between G sensor harness connector terminal and ground.
      + - Voltage
      (Approx.)
      G sensor
      Connector Terminal
      M83 3 Ground 5.0 V

    Is the inspection result normal?

    YES 

    GO TO STEP 4  .

    NO 

    GO TO STEP   8  .

  4. CHECK CIRCUIT BETWEEN TCM AND G SENSOR (PART 1)

    1. Turn ignition switch OFF.
    2. Disconnect TCM connector.
    3. Check continuity between TCM harness connector terminals and G sensor harness connector terminals.
      TCM G sensor Continuity
      Connector Terminal Connector Terminal
      F44 11 M83 2 Existed
      14 1

    Is the inspection result normal?

    YES 

    GO TO STEP 5. 

    NO 

    Repair or replace malfunctioning parts.

  5. CHECK CIRCUIT BETWEEN TCM AND G SENSOR (PART 2)

    Check continuity between TCM harness connector terminals and ground.

    TCM - Continuity
    Connector Terminal
    F44 14 Ground Not existed

    Is the inspection result normal?

    YES 

    GO TO STEP 6  .

    NO 

    Repair or replace malfunctioning parts.

  6. CHECK G SENSOR

    1. Remove G sensor. REMOVAL AND INSTALLATION .
    2. Connect the all connectors.
    3. Turn ignition switch ON.
    4. Check voltage between TCM harness connector terminal and ground.
      Fig 1: Checking G Sensor (With Consult-III)
      G06933081Courtesy of NISSAN NORTH AMERICA, INC.
      ARROWF : Direction of gravitational force
      + - Condition Voltage
      (Approx.)
      TCM
      Connector Terminal
      F44 14 Ground Vertical (- 1G) (A) 1.17 V
      Horizontal (B) 2.5 V
      Vertical (1G) (C) 3.83 V

    Is the inspection result normal?

    YES 

    GO TO STEP 7  .

    NO 

    Replace G sensor.REMOVAL AND INSTALLATION .

  7. G SENSOR CALIBRATION (PART 2)

    G-20With CONSULT 

    1. Install G sensor. REMOVAL AND INSTALLATION .
    2. Select "Self Diagnostic Results" in "TRANSMISSION".
    3. Touch "Erase".

    Perform "G SENSOR CALIBRATION". Refer to WORK PROCEDURE .

  8. CHECK SENSOR POWER SUPPLY CIRCUIT (PART 1)

    1. Turn ignition switch OFF.
    2. Disconnect TCM connector.
    3. Check continuity between TCM harness connector terminal and G sensor harness connector terminal.
      TCM G sensor Continuity
      Connector Terminal Connector Terminal
      F44 26 M83 3 Existed

    Is the inspection result normal?

    YES 

    GO TO STEP 9  .

    NO 

    Repair or replace malfunctioning parts.

  9. CHECK SENSOR POWER SUPPLY CIRCUIT (PART 2)

    Check continuity between TCM harness connector terminal and ground.

    TCM - Continuity
    Connector Terminal
    F44 26 Ground Not existed

    Is the inspection result normal?

    YES 

    Check intermittent incident. Refer to INTERMITTENT INCIDENT .

    NO 

    Repair or replace malfunctioning parts.

scientia non olet · About LEMON Manuals