LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2012 >> Cube Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 72 (Automatic Transmission) >> DTC Troubleshooting >> DTC P0982: Shift Solenoid Valve D (Short)

DTC P0982: Shift Solenoid Valve D (Short)

WARNING: This page is about a different car, the 2013 Honda Fit, 2012 Honda Fit, 2011 Honda Fit, 2010 Honda Fit, and 2009 Honda Fit. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information (see GENERAL TROUBLESHOOTING INFORMATION ).
  • This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
  • Some wire colors vary according to the model year, and are indicated with an asterisk as follows:
    • *(1): '09 - 10 models
    • *(2): '11 - 12 models
  1. Clear the DTC with the HDS.
  2. Start the engine in P, and wait for at least 1 second.
  3. Check that DTC P0982 recurs.

    Is DTC P0982 indicated? 

    YES  - go to step  7.

    NO  -Go to step 4.

  4. Select Shift Solenoid D in the Miscellaneous Test Menu, and test shift solenoid valve D with the HDS.

    Is a clicking sound heard? 

    YES  -Go to step 5.

    NO  - go to step  7.

  5. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  6. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the HDS indicate FAILED? 

    YES  -Go to step 7.

    NO  -Intermittent failure, the system is OK at this time. Check the SHD wire for an intermittent short to ground between shift solenoid valve D and the PCM. If the HDS indicates NOT COMPLETED, return to step  4 and recheck.

  7. Turn the ignition switch to LOCK (0).
  8. Jump the SCS line with the HDS.
  9. Disconnect PCM connector B (49P).
  10. Measure the resistance between PCM connector terminal B12 and body ground.
    Fig 1: Measuring Resistance Between PCM Connector Terminal B12 And Body Ground
    G06768398Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there less than 72 Ω? 

    YES  -Go to step 11.

    NO  - go to step  14.

  11. Disconnect the shift solenoid harness connector.
  12. Check for continuity between PCM connector terminal B12 and body ground.
    Fig 2: Checking Continuity Between PCM Connector Terminal B12 And Body Ground
    G06768399Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Repair a short in the wire between PCM connector terminal B12 and the shift solenoid harness connector, then go to step  19.

    NO  -Go to step 13.

  13. Inspect shift solenoid valve D (see SHIFT SOLENOID VALVE TEST ).

    Is shift solenoid valve D OK? 

    YES  -Go to step 14.

    NO  -Replace shift solenoid valve D or the shift solenoid harness (see SHIFT SOLENOID VALVE AND SHIFT SOLENOID WIRE HARNESS REPLACEMENT ), then go to step  19.

  14. Reconnect all connectors.
  15. Update the A/T software in the PCM if it does not have the latest software (see ECM/PCM UPDATE ), or substitute a known-good PCM (see SUBSTITUTING THE ECM/PCM ).
  16. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  17. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0982 indicated? 

    YES  -If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the PCM was substituted, go to step  1.

    NO  -Go to step 18.

  18. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the HDS indicate PASSED? 

    YES  -If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM (see ECM/PCM REPLACEMENT ). If any other DTCs were indicated on step 17, go to the indicated DTC's troubleshooting.

    NO  -Check for an intermittent short in the wire between shift solenoid valve D and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE ECM/PCM ), then recheck. If the PCM was substituted, go to step  1. If the HDS indicates NOT COMPLETED, return to step  16 and recheck.

  19. Reconnect all connectors.
  20. Clear the DTC with the HDS.
  21. Start the engine in P, and wait for at least 1 second. With the brake pedal pressed, shift to N, and wait for at least 1 second.
  22. Check for Pending or Confirmed DTCs with the HDS.

    Is DTC P0982 indicated? 

    YES  -Check for an intermittent short in the wire between shift solenoid valve D and the PCM, then go to step  1.

    NO  -Go to step 23.

  23. Monitor the OBD status for P0982 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.

    Does the HDS indicate PASSED? 

    YES  -Troubleshooting is complete. If any other DTCs were indicated on step 22, go to the indicated DTC's troubleshooting.

    NO  -Check for an intermittent short in the wire between shift solenoid valve D and the PCM, then go to step  1. If the HDS indicates NOT COMPLETED, return to step  21 and recheck.

scientia non olet · About LEMON Manuals