LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Altima S, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1167 (Engine Control System - DTCS P1225 To P2A03) >> P1564 ASCD Steering Switch >> Diagnosis Procedure

Diagnosis Procedure

WARNING: This page is about a different car, the 2009 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK GROUND CONNECTION
    1. Turn ignition switch OFF.
    2. Check ground connection E9. Refer to Ground Inspection in "CIRCUIT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 2.

    NO: Repair or replace ground connection.

  2. CHECK ASCD STEERING SWITCH CIRCUIT

    With CONSULT-III 

    1. Turn ignition switch ON.
    2. Select "MAIN SW", "CANCEL SW", "RESUME/ACC SW" and "SET SW" in "DATA MONITOR" mode with CONSULT-III.
    3. Check each item indication under the following conditions.
    MONITOR ITEM CONDITION CHART

    Monitor item Condition Indication
    MAIN SW MAIN switch Pressed ON
    Released OFF
    CANCEL SW CANCEL switch Pressed ON
    Released OFF
    RESUME/ACC SW RESUME/ACCELERATE switch Pressed ON
    Released OFF
    SET SW SET/COAST switch Pressed ON
    Released OFF

    Without CONSULT-III 

    1. Turn ignition switch ON.
    2. Check the voltage between ECM harness connector terminals under the following conditions.
    VOLTAGE SPECIFICATION

    ECM Condition Voltage (V)
    Connector + -
    Terminal Terminal
    E10 85 (ASCD steering switch signal) 92 (ASCD steering switch ground) MAIN switch: Pressed Approx. 0
    CANCEL switch: Pressed Approx. 1
    SET/COAST switch: Pressed Approx. 2
    RESUME/ACCELERATE switch: Pressed Approx. 3
    All ASCD steering switches: Released Approx. 4
    Fig 1: Checking Voltage Between ECM Harness Connector Terminals
    G05869925Courtesy of NISSAN MOTOR CO., U.S.A.

    Is the inspection result normal? 

    YES: GO TO 8.

    NO: GO TO 3.

  3. CHECK ASCD STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Disconnect combination switch harness connector.
    4. Check the continuity between combination switch and ECM harness connector.
      CONTINUITY CHART

      Combination switch ECM Continuity
      Terminal Connector Terminal
      16 E10 92 Existed
    5. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: GO TO 5.

    NO: GO TO 4.

  4. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E30, M11
    • Combination switch (spiral cable)
    • Harness for open and short between ECM and combination switch

    : Repair open circuit, short to ground or short to power in harness or connectors.

  5. CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Check the continuity between combination switch and ECM harness connector.
      CONTINUITY CHART

      Combination switch ECM Continuity
      Terminal Connector Terminal
      13 E10 85 Existed
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: GO TO 7.

    NO: GO TO 6.

  6. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness connectors E30, M1
    • Combination switch (spiral cable)
    • Harness for open and short between ECM and combination switch

    : Repair open circuit, short to ground or short to power in harness or connectors.

  7. CHECK ASCD STEERING SWITCH

    Refer to "COMPONENT INSPECTION ".

    Is the inspection result normal? 

    YES: GO TO 8.

    NO: Replace ASCD steering switch.

  8. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

scientia non olet · About LEMON Manuals