LEMON Manuals: Even more car manuals for everyone
Home >> Mitsubishi >> 2014 >> Lancer ES Sportback >> Repair and Diagnosis >> External Pages >> Different car >> Section 63 (Electronically Controlled AWD - With Diagnostics) >> Troubleshooting >> Diagnostic Trouble Code Procedures >> Code No. C1219: Steering Wheel Sensor Signal >> Diagnosis

Code No. C1219: Steering Wheel Sensor Signal: Diagnosis

WARNING: This page is about a different car, the 2014 Mitsubishi Outlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. STEP 1. Scan tool (M.U.T.-III) CAN bus diagnostics. 

    Use scan tool (M.U.T.-III) to perform the CAN bus diagnosis.

    Q: Is the check result normal? 

    1. YES:  Go to  Step 3.
    2. NO:  Repair the CAN bus lines (Refer to DIAGNOSIS ). After repairing the CAN bus line, go to Step 2.
  2. STEP 2. Check whether the DTC is stored again. 

    Q: Is DTC No. C1219 stored? 

    1. YES:  Go to Step 3.
    2. NO:  This diagnosis is complete.
  3. STEP 3. Scan tool (M.U.T.-III) DTC. 

    Q: Is DTC No. C2205 stored? 

    1. YES:  Perform the relevant troubleshooting.
    2. NO:  Go to Step 4.
  4. STEP 4. Scan tool (M.U.T.-III) DTC. 

    Check if the wheel speed sensor-related, G and yaw rate sensor-related, or steering wheel sensor-related DTC is stored.

    Q: Is the DTC stored? 

    1. YES:  Carry out the appropriate troubleshooting. Then go to  Step 9.
    2. NO:  Go to Step 5.
  5. STEP 5. Check of steering wheel sensor installation status 

    Check that the steering wheel sensor is installed correctly (Refer to STEERING WHEEL SENSOR ).

    Q: Is the check result normal? 

    1. YES:  Go to Step 6.
    2. NO:  Install the steering wheel sensor correctly. Then go to Step 6.
  6. STEP 6. Wheel alignment check 

    Q: Is the check result normal? 

    1. YES:  After checking the wheel alignment, calibrate the steering wheel sensor (Refer to STEERING WHEEL SENSOR CALIBRATION ), and reset the steering wheel sensor correction amount stored in the AWD-ECU (Refer to AWD-ECU  ). Then, go to Step 7.
    2. NO:  After adjusting the wheel alignment, calibrate the steering wheel sensor (Refer to STEERING WHEEL SENSOR CALIBRATION ), and reset the steering wheel sensor correction amount stored in the AWD-ECU (Refer to AWD-ECU  ). Then, go to Step 7.
  7. STEP 7. Scan tool (M.U.T.-III) data list. 

    Check the following data list (Refer to DATA LIST REFERENCE TABLE  ).

    • Item No.8: Steering angle sensor

    Q: Is the check result normal? 

    1. YES:  Go to Step 8.
    2. NO:  Replace the steering wheel sensor (Refer to STEERING WHEEL SENSOR ). Then, go to  Step 9.
  8. STEP 8. Check whether the DTC is stored again. 

    Q: Is DTC No. C1219 stored? 

    1. YES:  Replace the AWD-ECU (Refer to AWD-ECU  ). Then, go to Step 9.
    2. NO:  Intermittent malfunction (Refer to HOW TO COPE WITH INTERMITTENT MALFUNCTION ).
  9. STEP 9. Check whether the DTC is stored again. 

    Q: Is DTC No. C1219 stored? 

    1. YES:  Return to  Step 1.
    2. NO:  This diagnosis is complete.
scientia non olet · About LEMON Manuals