11 41 000 Removing and Installing/Replacing Oil Pump (N55) (up to production date March 2012)

WARNING: This page does not describe the selected car, but rather 21 other vehicles, including the 2017 BMW 550i GT xDrive, 2017 BMW 535i GT xDrive, 2017 BMW 535i GT, 2016 BMW 550i GT xDrive, and 2016 BMW 535i GT xDrive. However, it is still accessible from the selected car via links, so may be relevant.

Special Tools Required:

11 4 120 .
2 303 793 .

IMPORTANT: Aluminum Screws/Bolts Must Be Replaced Each Time They Are Released .
Aluminum Screws/Bolts Are Permitted with and Without Color Coding (Blue).
for Reliable Identification:
Aluminum Screws/Bolts Are Not Magnetic .
Joining Torque and Angle of Rotation Must Be Observed Without Fail (Risk of Damage) .

Necessary Preliminary Tasks:

Remove OIL SUMP .
Remove SEALING CAP of Vacuum Pump.

Undo All The Aluminum Screws (1) Along The Line.

Installation Note:

Replace Aluminum Screws.

Remove Intake Pipe with Oil Deflector.

Installation Note:

Replace O-Ring.

Fig 1: Removing Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Press Timing Chain with Chain Tensioner (1) In Direction of Arrow.

Disconnect Timing Chain with Special Tool 11 4 120 .

Feed Out Camshaft Sprocket (3) At Hexagon Head (4) of Vacuum Pump.

Installation Note:

If The Chain Module Is Replaced, A Mounting Bar (2) Is Already Pre-Installed.

Fig 2: Pressing Timing Chain with Chain Tensioner

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Sprocket Must Be Blocked In Order To Release Central Bolt (1).

Secure Special Tool 2 303 793 To Crankcase.

Release Oil Pump Central Bolt (1).

Tightening torque 11 41 5AZ .

Fig 3: Releasing Oil Pump Central Bolt Using Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Release Aluminum Screws (1).

Tightening torque 11 41 6AZ .

Installation Note:

Replace Aluminum Screws.

Watch Mounting Flats On Oil Pump Sprocket.

Fig 4: Identifying Oil Pump Drive Gear and Aluminum Screws

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Observe Different Screw Lengths.

Release Aluminum Screws (1).

Tightening torque 11 41 2AZ .

Installation Note:

Replace Aluminum Screws.

Fig 5: Identifying Aluminum Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Detach Sprocket (1) In Direction of Arrow.

NOTE: Chain Tensioner Presses Timing Chain (3) Upwards.
Do Not Remove Sprocket (1).

Remove Oil Pump (2) In Direction of Arrow.

Fig 6: Detaching Sprocket and Removing Oil Pump

Courtesy of BMW OF NORTH AMERICA, INC.

Installation Note:

Check Spacer Bushes for Secure Seating and Damage; Replace If Necessary.

Fig 7: Locating Spacer Bushes

Courtesy of BMW OF NORTH AMERICA, INC.

Install Oil Pump (2).

Align Mounting Flats (3) On Oil Pump (2) To Sprocket (4).

Fig 8: Identifying Oil Pump, Twin Surface, and Spacer Bushings

Courtesy of BMW OF NORTH AMERICA, INC.

Install Intake Pipe with Oil Deflector.

Installation Note:

Replace O-Ring.

Insert All The Aluminum Screws (1) Along The Line.

Installation Note:

Replace Aluminum Screws.

Tightening torque 11 41 1AZ .

Fig 9: Identifying Aluminum Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Assemble Engine.