51 46 018 Removing and installing/replacing trim panel for storage shelf with roller sunblind

WARNING: This page does not describe the selected car, but rather 18 other vehicles, including the 2015 BMW Alpina B7L xDrive, 2015 BMW Alpina B7 xDrive, 2015 BMW 750i xDrive, 2015 BMW 750Li xDrive, and 2015 BMW 740Li xDrive. However, it is still accessible from the selected car via links, so may be relevant.

Necessary preliminary tasks:

Remove backrest. See REMOVING BACKREST FOR REAR SEAT (NORMAL) or REMOVING BACKREST FOR REAR SEAT (ELECTRIC) .
Only with optional equipment Comfort seat:
- Remove HEAD RESTRAINTS .
- Remove ARMREST .
With rear air conditioning optional equipment only: Remove LUGGAGE COMPARTMENT PARTITION WALL .
Remove TRIM FOR ROOF PILLAR AT REAR .
Remove BELT FEED TRIM on left and right.

Release screws in luggage compartment.

Installation note:

Tightening torque 51 46 2AZ .

Fig 1: Identifying Luggage Compartment And Screws

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Graphics are only an example (The graphics used are from F01).

Lever out center seat belt finisher strip (1) with plastic wedge and feed out seat belt strap (2).

Fig 2: Identifying Center Seat Belt Finisher Strip And Seat Belt Strap

Courtesy of BMW OF NORTH AMERICA, INC.

Version with decorative strip only:

Unclip center seat belt finisher strip (1) from decorative trim and feed out seat belt strap (2).

Fig 3: Identifying Center Seat Belt Finisher Strip And Seat Belt Strap

Courtesy of BMW OF NORTH AMERICA, INC.

Release plastic nut (1) on C-pillar trim panel.

Fig 4: Identifying C-Pillar Trim Panel Plastic Nut
Courtesy of BMW OF NORTH AMERICA, INC.

Release plastic nut (1) on C-pillar trim panel.
Disengage guide lug of C-pillar trim panel at top from storage shelf.

Fig 5: Identifying C-Pillar Trim Panel Plastic Nut
Courtesy of BMW OF NORTH AMERICA, INC.

Release attachment sleeves and pull storage shelf forwards.

Unlock and disconnect underlying plug connections.

Fig 6: Pulling Storage Shelf

Courtesy of BMW OF NORTH AMERICA, INC.

Replacement:

Remove SPEAKERS (SUPPORT) on left/right.
Remove ROLLER SUNBLIND .

Version with Top Tether eyelets only:

Lever out all caps (1) for Top Tether eyelets with plastic wedge.

Fig 7: Removing Top Tether Eyelets Caps

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note:

Retaining lugs must not be damaged.

If necessary, replace cap.

Fig 8: Identifying Retaining Lugs

Courtesy of BMW OF NORTH AMERICA, INC.

Press retaining lugs and remove frame for Top Tether eyelet trim.

Installation note:

Make sure retaining lugs are correctly seated in aperture.

Fig 9: Locating Retaining Lugs

Courtesy of BMW OF NORTH AMERICA, INC.

Version with decorative strip only:

Release screws (1).

Remove decorative strip.

Fig 10: Identifying Decorative Strip Mounting Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Work on apertures in trim panel, depending on equipment specification:

IMPORTANT: Only work on clean surfaces. Risk of dirtying storage shelf.
Storage shelf must lie flat to punch out the holes.
Make sure cut edges are clean.
Fabric cover must not pull any threads.

Fig 11: Identifying Decorative Strip Apertures And Cut Out Apertures

Courtesy of BMW OF NORTH AMERICA, INC.

Pay attention to molding on storage shelf:

Cut out apertures for Top Tether eyelet or belt feed with a Fein cutter (160 A) or with a bodywork saw with blade for curved cuts.
Punch out decorative strip apertures.