11 31 038 Removing And Installing / Replacing Right Exhaust Camshaft (S85)

WARNING: This page does not describe the selected car, but rather 10 other vehicles, including the 2010 BMW M6, 2010 BMW M5, 2009 BMW M6, 2009 BMW M5, and 2008 BMW M6. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

11 5 241
11 5 242
11 5 243

Necessary preliminary tasks:

IMPORTANT: Use only special tool 11 5 241 to remove and install camshafts.

To remove and install the exhaust camshafts, special tool 11 5 243 is not required and must be removed from special tool 11 5 241.

Fig 1: Identifying Special Tool 11 5 241, 11 5 242 And 11 5 243

Courtesy of BMW OF NORTH AMERICA, INC.

Secure special tool 11 5 241 to cylinder head on left with special tool 11 5 242.

IMPORTANT: Screw in special tool 11 5 242 to max. 30 Nm.

Pretension eccentric shaft (2) at hexagon head in direction of arrow.

Lock (1) must snap audibly into place.

Fig 2: Pretensioning Eccentric Shaft At Hexagon Head

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws (1).

Tightening torque: 11 31 4AZ. See CAMSHAFT .

E Inlet camshaft.

A Exhaust camshaft.

IMPORTANT: Risk of mix-up with cylinder bank 6-10.
Arrow must point in direction of travel to chain drive.

Remove bearing caps.

Fig 3: Identifying Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Lubricate all bearing points with engine oil.

Release screws along lines (1).

Tightening torque: 11 31 4AZ. See CAMSHAFT .

Installation:

Lubricate all bearing points with engine oil.

NOTE: Illustration does not show special tool 11 5 241.

Fig 4: Identifying Lines

Courtesy of BMW OF NORTH AMERICA, INC.

Release lock (1) on special tool 11 5 241.

Relieve tension on eccentric shaft at hexagon head in direction of arrow.

IMPORTANT: Inlet camshaft is pressed upwards by valve springs.
Exhaust camshaft must lift off uniformly in upward direction.

Fig 5: Relieving Tension On Eccentric Shaft At Hexagon Head (1 Of 2)

Courtesy of BMW OF NORTH AMERICA, INC.

Insert exhaust camshaft, cylinders 1-5.

Designation (A 2) on dihedron points upwards.

Installation:

Lubricate all bearing points with engine oil.

Fig 6: Relieving Tension On Eccentric Shaft At Hexagon Head (2 Of 2)

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

All bearing shells are assigned to one cylinder.

E and A from (1 to 10), e.g. A 1= exhaust side on 1st cylinder.

Arrow (1) must point in direction of travel to chain drive.

Fig 7: Identifying Designation (A1) On Dihedron

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Arrangement of bearing shells, cylinders 1 to 5.

IMPORTANT: Mixing them up will result in increased wear - risk of damage!

Fig 8: Identifying Installation Sequence Of Bearing Shells

Courtesy of BMW OF NORTH AMERICA, INC.

Mount special tool 11 5 241 with special tool 11 5 242.

Pretension eccentric shaft (1) at hexagon head in direction of arrow.

IMPORTANT: Exhaust camshaft is pressed upwards by valve springs.

Lock must snap audibly into place.

Install all bearing caps by numbers.

Tightening torque 11 31 4AZ. See CAMSHAFT .

Adjust valve timing.

Assemble engine.

Fig 9: Pretensioning Eccentric Shaft At Hexagon Head

Courtesy of BMW OF NORTH AMERICA, INC.