Remove/Install Automatic Transmission Fluid Cooler - AR27.55-P-1000MSC
Transmission 725.0 in model 167 with engine 176, 256.9
MODIFICATION NOTES
| 17.07.2019 | Bleeding routine added. | AS 9 |
Shown on model 167 with engine 256.9
Fig 1: Automatic Transmission Fluid Cooler Components Location - Transmission 725.0 In Model 167 With Engine 176, 256.9 (Shown With Engine 256.9)
| Risk of injury to skin and eyes suffering scalding from contact with hot coolantspray. Risk of poisoning from swallowing coolant. | Do not open cooling system unless coolant temperature is below 90 °C. Open cap slowly and release the overpressure. Do not pour coolant into beverage containers. Wear protective gloves, protective clothing and safety glasses. |
AS20.00-Z-0001-01A | |
| Risk of injury to skin and eyes due to handling of transmission oil. Health risk caused by swallowing transmission oil | Wear protective gloves, protective clothing and safety glasses. Do not pour transmission oil into beverage bottles. |
AS00.40-Z-0001-01A | |
| Notice | Notes on avoiding damage through contamination and foreign objects | AH00.00-P-5000-01A | |
| Notes on automatic transmission | AH27.19-P-0001-01NKB | ||
| Remove/install | |||
| 1 | Remove upper engine cover. | ||
| Transmission 725.0 in model 167 with engine 176 | AP01.10-P-2405-01M | ||
| Transmission 725.0 in model 167 with engine 256.9 |
AR01.10-P-2405MSC | ||
| 2 | Remove engine air intake duct upstream of air filter. | ||
| 3 | Remove oil lines (3) from oil cooler (1) and seal with suitable stop plugs. | AR27.10-P-0501-03LF | |
| Fig 3 | |||
| 4 | Clam p off coolant hoses (2). | Fig 4 | |
| 5 | Remove coolant hoses (2) from oil cooler (1) and seal openings with protective covers. | AR20.20-P-7441-01RQ | |
| Fig 2 | |||
| 6 | Push retaining clamp (4) upwards and remove oil cooler (1). | Push the retaining clip (4) up carefully. Otherwise, the retaining clamp (4) will be damaged. If the retaining clamp (4) is damaged, ↓ fasten oil cooler (1) at position marked by arrow using repair bolt and washer. |
|
| 7 | Install in the reverse order. | ||
| Check | |||
| 8 | Check and correct oil level in automatic transmission. | AR27.00-P-0270EWN | |
| 9 | Connect diagnostic unit device perform bleeding routine. | ||
| AD00.00-P-2000-06ME | |||
| 10 | Check engine cooling system for leak tightness. | Transmission 725.0 in model 167 with engine 176 | AR20.00-P-1011MNO |
| Transmission 725.0 in model 167 with engine 256.9 | AR20.00-P-1010MSC | ||
| Risk of accident from vehicle starting off by itself when engine running. Risk of injury (bruises and burns) resulting from working on the engine while it is being started or when it is running. | Secure vehicle to prevent it from starting off by itself. Wear closed and snug - fitting work clothes. Do not touch hot or rotating parts. | AS00.00-Z-0005-01A | |
| 11 | Carry out engine test run and check engine for proper leak tightness and leak tightness. | ||
| 12 | Install upper engine cover. | Transmission 725.0 in model 167 with engine 256.9 | AR01.10-P-2405MSC |
| Transmission 725.0 in model 167 with engine 176 | AP01.10-P-2405-01M |