Rear Fender Complete Replacement - Ar63.50-P-1401MFD

Model 118.3 

Fig 1: Quarter Panel Component Location

Courtesy of MERCEDES-BENZ USA

	Risk of explosion  caused by fuel igniting, risk of poisoning caused by inhaling and swallowing fuel as well as risk of injury to eyes and skin caused by contactwith fuel.	No fires, sparks, open flames or smoking. Pour fuels into suitable and appropriately marked containers only. Wear protective clothing when handling fuel.	AS47.00-Z-0001-01A
	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Risk of injury  . Skin or eye injuries may result when handling hot or glowing objects.	Wear protective gloves, protective clothing and safety glasses, if necessary.	AS00.00-Z-0002-01A
	Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
Notice	General information on body repair		AH60.00-P-0001-01KOA
Notice	Pretreatment of bonding surfaces		AH60.00-P-0008-01SX
Notice	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Notes on acoustic foam and structural foam in the vehicle		AH60.00-P-0039-01MFA
	General information on MB materials		AH98.00-P-9409-03A
	Remove
1	Remove all detachable parts in area of repair point.
2	Cover all detachable parts remaining in vehicle with spark protection blanket.	When installing a new rear left fender (1), the standard fuel filler cap must be installed and the filler neck must be covered with a spark protection blanket. Commercially available devices/tools  Spark protection blankets
3	Remove rear fender (1).		AR63.50-P-1400-02MFD
	000 588 15 84 00 Heat gun	Commercially available devices/tools  Round wire brush Body power jigsaw Spot weld milling machine Wet/dry vacuum cleaner	WS54.00-P-0125B
		1K-zinc dust paint	*BR00.45-Z-1056-07A
4	Prepare rear fender (1).	Commercially available devices/tools  Round wire brush Body power jigsaw	AR63.50-P-1400-03MFD
		1K-zinc dust paint	*BR00.45-Z-1056-07A
	Install
	Risk of explosion and poisoning  caused by solvent vapors and gasses. Risk of injury  to skin and eyes when working with anticorrosion agents	Never spray corrosion protection on flames or hot, glowing objects and keep them well away from all potential sources of ignition. Use them only in well-ventilated rooms; wear respiratory protection.	AS97.00-Z-0001-01A
	Risk of explosion  caused by paint vapors igniting. Risk of poisoning  caused by inhaling paint vapors.	No smoking! No open fire! Use respiratory protection, protective clothing, gloves, safety glasses and protective skin cream. Ensure that the area is well ventilated.	AS98.00-Z-0002-01A
	The high voltage used for electric welding presents a lethal hazard. Risk of explosion  from welding in areas close to highly inflammable materials. Risk of injury  from weld splatter and UV-light when welding. Risk of poisoning  from inhaling welding gases	Use insulating mats. Wear protective clothing, safety glasses and a protective mask. Remove highly inflammable materials from the hazard area. Use air extraction system.	AS00.00-Z-0007-01A
Notice	Measures for preventing damage to components when performing electric welding and soldering work		AH60.00-P-0001-02A
	General information on riveting		AH60.00-P-0003-01N
5	Install rear fender (1).		AR63.50-P-1400-04MFD
	000 588 12 84 00 Welder		WS00.00-P-0318K
	000 588 13 84 00 Welder		WS60.00-P-0437K
		Gap dimensions on hoods, doors and lids	AR60.00-P-0700-01MFC
		Process filler on body As an alternative to the restoring the surfaces with the body solder, a body basic spatula can also be used. Commercially available devices/tools  Round wire brush Blind rivet gun (minimum pull-off force 19 kN) Hand riveter Wet/dry vacuum cleaner	AR60.00-P-0031-01LWG
		Basic body filler	*BR00.45-Z-1057-07A
		Rear door to side wall	*BE60.00-P-1011-01NA
		Bumper at rear to side wall	*BE60.00-P-1022-01NA
		Outer tail lamp to side wall	*BE60.00-P-1017-01NA
		Liftgate/trunk lid to side wall	*BE60.00-P-1015-01NA
		Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	*BE60.00-P-1012-01NA
		1K-zinc dust paint	*BR00.45-Z-1056-07A
		White sealing compound, 310 ml, DBL 6069.20	*BR00.45-Z-1003-01A
		Parts kit for 2-component adhesive for body	*BR00.45-Z-1162-02A
		Blind rivet Y2 6.5x12.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN)	*BR00.45-Z-1012-13A
		Feeler gauge	Fig 2
6	Clean weld joints and sheet metal flange.	Commercially available devices/tools  Round wire brush
7	Remove spark protection blankets.	Commercially available devices/tools  Spark protection blankets
8	Clean repair area.	Commercially available devices/tools  Wet/dry vacuum cleaner
9	Treat repair areas with primer filler.
Notice	Notes on paintwork repairs		AH98.00-P-9408-02A
	General information on operation items and work procedures for painting	Use only primer filler approved by Daimler AG: http://xentryportal.mercedes-benz.com	AH98.00-P-0003-01A
10	Seal seam after repair.		AR97.10-P-4000-03MFA
		Seam sealant, sprayable 310 ml	*BR00.45-Z-1041-01A
		White sealing compound, 310 ml, DBL 6069.20	*BR00.45-Z-1003-01A
11	Paint repair areas and adjacent surfaces.
Notice	Notes on paintwork repairs		AH98.00-P-9408-02A
	General information on operation items and work procedures for painting	Use only paints approved by Daimler AG: http://xentryportal.mercedes-benz.com	AH98.00-P-0003-01A
12	Supplement cavity preservation.	Commercially available devices/tools  Pressure spray gun	AR97.20-P-1500MFA
		Cavity preservation (free of solvents), 1 liter	*BR00.45-Z-1003-05A
13	Install all detachable parts in area of repair point.

GAP DIMENSIONS

Number	Designation			Model 118.3
BE60.00-P-1011-01NA	Rear door to side wall	Dimension "I"	mm	3, 5 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC

GAP DIMENSIONS

Number	Designation			Model 118.3
BE60.00-P-1012-01NA	Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	Dimension "J"	mm	2 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC

GAP DIMENSIONS

Number	Designation			Model 118.3
BE60.00-P-1015-01NA	Liftgate/trunk lid to side wall	Dimension "M"	mm	3, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFC

GAP DIMENSIONS

Number	Designation			Model 118.3
BE60.00-P-1017-01NA	Outer tail lamp to side wall	Dimension "O"	mm	1, 5 (±0, 5)

GAP DIMENSIONS

Number	Designation			Model 118.3
BE60.00-P-1022-01NA	Bumper at rear to side wall	Dimension "T"	mm	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFC

Fig 2: Feeler Gauge (129 589 03 21 00)

Courtesy of MERCEDES-BENZ USA

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1003-01A	White sealing compound, 310 ml, DBL 6069.20	A 001 989 63 20
BR00.45-Z-1003-05A	Cavity preservation (free of solvents), 1 liter	A 000 986 72 70 10
BR00.45-Z-1012-13A	Blind rivet Y2 6.5x12.5 (clamping range 2 mm to 5 mm, draw-off strength min. 19 kN)	A 004 990 16 97
BR00.45-Z-1041-01A	Seam sealant, sprayable 310 ml	A 002 989 84 20
BR00.45-Z-1056-07A	1K-zinc dust paint	A 000 986 28 00
BR00.45-Z-1057-07A	Basic body filler	A 012 989 29 71
BR00.45-Z-1162-02A	Parts kit for 2-component adhesive for body	A 012 989 17 71