Remove/Install Driver Door Upper Hinge - AR72.10-P-0006ME

Model 167 

Courtesy of MERCEDES-BENZ USA

	Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
Notice	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
Notice	Notes on self-locking nuts and bolts		AH00.00-P-0001-01KOA
	Notes on safety-relevant components		AH00.00-Z-0019-01A
	Remove
1	Remove driver's door.		AR72.10-P-0500ME
2	Mark installation position of hinge leaf (1.1) and hinge support (1.2) using suitable means.	The upper hinge consists of hinge leaf (1.1) and hinge support (1.2).
3	Remove screws (2) and remove hinge leaf (1.1).
4	Remove instrument panel.		AR68.10-P-1000ME
5	Remove control units in area of A-pillar and release cable duct until nuts (3) can be accessed.	Cable duct is secured with a guide to metal bracket.
		The number of control units varies depending on the vehicle equipment.
6	Remove nuts (3) and remove hinge support (1.2).	Press damping if necessary to the side.
	Install
7	Clean contact surfaces in area of hinge supports.	Cleaner	*BR00.45-Z-1025-04A
8	Align hinge leaf (1.1) based on the previously applied markings to the driver's door and tighten screws (2) slightly by hand.
9	Align hinge support (1.2) by means of the previously applied markings and slightly tighten nuts (3) by hand.
10	Install driver's door.		AR72.10-P-0500ME
11	Close and open driver's door.	The installation position of the driver door may change later due to opening and closing.
	Check
12	Check gap dimensions at driver's door, adjust if necessary.		AR72.10-P-0550ME
13	Tighten screws (2) and nuts (3).	Helper required.
		Screw/bolt, hinge to front door	*BA72.10-P-1002-01O
		Bolt/nut, hinge to A-pillar	*BA72.10-P-1003-01O
14	Repair paint damage at respective bolt heads.	Overview of MB materials and how they are processed	AR98.00-P-0150CW
	Risk of explosion and poisoning  caused by solvent vapors and gasses. Risk of injury  to skin and eyes when working with anticorrosion agents	Never spray corrosion protection on flames or hot, glowing objects and keep them well away from all potential sources of ignition. Use them only in well-ventilated rooms; wear respiratory protection.	AS97.00-Z-0001-01A
15	Protect driver's door and A-pillar in the area of the hinge leaf (1.1) and hinge support (1.2) against corrosion; remove excess wax.	Wax for engine compartment (400 ml spray can)	*BR00.45-Z-1018-05A
16	Mount cable duct and install control units in area of A-pillar.	Mount cable duct with guide on metal bracket.
17	Install instrument panel.		AR68.10-P-1000ME

FRONT DOOR

Number	Designation		Model 167
BA72.10-P-1002-01O	Screw/bolt, hinge to front door	Nm	32

FRONT DOOR

Number	Designation		Model 167
BA72.10-P-1003-01O	Bolt/nut, hinge to A-pillar	Nm	40

REPAIR MATERIALS

Number	Designation	Order number
BR00.45-Z-1018-05A	Wax for engine compartment (400 ml spray can)	A 000 986 33 70 10
BR00.45-Z-1025-04A	Cleaner	A 005 989 19 71