Perform Initial Accident Diagnosis - Ar60.00-P-1105MFA

Model 118, 177, 247 

MODIFICATION NOTES

25.06.2019

Rear door to side wall

Model 247.0

BE60.00-P-1011-01MA

	Risk of death  caused by vehicle slipping or toppling off of the lifting platform.	Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer.	AS00.00-Z-0010-01A
	Risk of injury  caused by scraping or cutting body parts on sharp vehicle parts	Always wear protective gloves when working on or near sharp and non-deburred vehicle parts. Deburr repair panels.	AS00.00-Z-0017-01A
	Evaluating steering gear when repairing accident vehicles		AH46.20-P-9409-01A
	Check
1	Print out checklist and document the following tests.
			OF60.00-P-1000-01MFA
2	Check vehicle exterior in the visible area for damage.
		Model 177	AP60.00-P-0050L
		Model 247	AP60.00-P-0050O
		Model 118	AP60.00-P-0050Q
3	Check gaps.	Model 118	AR60.00-P-0700-01MFC
		Model 177 Model 247	AR60.00-P-0700-01MFA
		Model 118.3	*BE60.00-P-1001-01NA
		Model 118.6
		Engine hood to bumper
		Model 118.3	*BE60.00-P-1002-01NA
		Model 118.6 Engine hood to fender
		Model 118.3 Model 118.6 Headlamp top to bumper	*BE60.00-P-1003-01NA
		Model 118.3 Model 118.6 Headlamp front to bumper	*BE60.00-P-1004-01NA
		Model 118.3 Model 118.6 Headlamp bottom to bumper	*BE60.00-P-1005-01NA
		Model 118.3 Model 118.6 Headlamp to fender	*BE60.00-P-1006-01NA
		Model 118.3 Model 118.6 Fender to bumper at front	*BE60.00-P-1007-01NA
		Model 118.3 Model 118.6 Fender to side wall (A-pillar)	*BE60.00-P-1008-01NA
		Model 118.3 Model 118.6 Front door to fender	*BE60.00-P-1009-01NA
		Model 118.3 Model 118.6 Front door to rear door	*BE60.00-P-1010-01NA
		Model 118.3 Model 118.6 Rear door to side wall	*BE60.00-P-1011-01NA
		Model 118.3 Model 118.6 Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	*BE60.00-P-1012-01NA
		Model 118.3 Model 118.6 Roof spoiler to side wall	*BE60.00-P-1013-01NA
		Model 118.3 Model 118.6 Roof spoiler to roof	*BE60.00-P-1014-01NA
		Model 118.3 Model 118.6 Liftgate/trunk lid to side wall	*BE60.00-P-1015-01NA
		Model 118.3 Model 118.6 Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01NA
		Model 118.3 Model 118.6 Outer tail lamp to side wall	*BE60.00-P-1017-01NA
		Model 118.3 Model 118.6 Outer tail lamp to bumper at rear	*BE60.00-P-1018-01NA
		Model 118.3 Model 118.6 Outside of taillamp to inside of taillamp	*BE60.00-P-1019-01NA
		Model 118.3 Model 118.6 Liftgate/trunk lid to inner tail lamp (top)	*BE60.00-P-1020-01NA
		Model 118.3 Model 118.6 Liftgate/trunk lid to inner tail lamp (bottom)	*BE60.00-P-1021-01NA
		Model 118.3 Model 118.6 Bumper at rear to side wall	*BE60.00-P-1022-01NA
		Model 118.3 Model 118.6 Trunk lid to rear window	*BE60.00-P-1023-01NA
		Model 118.3 Model 118.6 Longitudinal member panel to front door/rear door	*BE60.00-P-1024-01NA
		Model 247.0 Longitudinal member panel to front door/rear door	*BE60.00-P-1025-01MA
		Model 247.0 Longitudinal member panel to fender	*BE60.00-P-1024-01MA
		Model 247.0 Bumper at rear to side wall	*BE60.00-P-1023-01MA
		Model 247.0 Tailgate/trunk lid to inner tail lamp (bottom)/rear continuous reflector strip (bottom)	*BE60.00-P-1022-01MA
		Model 247.0 Tailgate/trunk lid to inner tail lamp (top)/rear continuous reflector strip (top)	*BE60.00-P-1021-01MA
		Model 247.0 Outer tail lamp to inner tail lamp/rear continuous reflector strip	*BE60.00-P-1020-01MA
		Model 247.0 Outer tail lamp to liftgate	*BE60.00-P-1019-01MA
		Model 247.0 Outer tail lamp to bumper at rear	*BE60.00-P-1018-01MA
		Model 247.0 Outer tail lamp to side wall	*BE60.00-P-1017-01MA
		Model 247.0 Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01MA
		Model 247.0 Liftgate/trunk lid to side wall	*BE60.00-P-1015-01MA
		Model 247.0 Roof spoiler to roof	*BE60.00-P-1014-01MA
		Model 247.0 Roof spoiler to side wall	*BE60.00-P-1013-01MA
		Model 247.0 Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	*BE60.00-P-1012-01MA
		Model 247.0 Rear door to side wall	*BE60.00-P-1011-01MA
		Model 247.0 Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01MA
		Model 247.0 Front door to rear door	*BE60.00-P-1009-01MA
		Model 247.0 Front door to fender	*BE60.00-P-1008-01MA
		Model 247.0 Fender to side wall (A-pillar)	*BE60.00-P-1007-01MA
		Model 247.0 Fender to bumper at front	*BE60.00-P-1006-01MA
		Model 247.0 Headlamp to fender	*BE60.00-P-1005-01MA
		Model 247.0 Headlamp bottom to bumper	*BE60.00-P-1004-01MA
		Model 247.0 Headlamp front to bumper	*BE60.00-P-1003-01MA
		Model 247.0 Engine hood to fender	*BE60.00-P-1002-01MA
		Model 247.0 Engine hood to bumper	*BE60.00-P-1001-01MA
		Model 177.0 Model 177.1/9 Longitudinal member panel to fender/front door/rear door	*BE60.00-P-1025-01JA
		Model 177.1/9 Trunk lid to rear window	*BE60.00-P-1024-01JA
		Model 177.0 Model 177.1/9 Bumper at rear to side wall	*BE60.00-P-1023-01JA
		Model 177.0 Model 177.1/9 Liftgate/trunk lid to inner tail lamp (bottom)	*BE60.00-P-1022-01JA
		Model 177.0 Model 177.1/9 Liftgate/trunk lid to inner tail lamp (top)	*BE60.00-P-1021-01JA
		Model 177.0 Model 177.1/9 Outside of taillamp to inside of taillamp	*BE60.00-P-1020-01JA
		Model 177.0 Outer tail lamp to liftgate	*BE60.00-P-1019-01JA
		Model 177.0 Model 177.1/9 Outer tail lamp to bumper at rear	*BE60.00-P-1018-01JA
		Model 177.0 Model 177.1/9 Outer tail lamp to side wall	*BE60.00-P-1017-01JA
		Model 177.0 Model 177.1/9 Liftgate/trunk lid to bumper at rear	*BE60.00-P-1016-01JA
		Model 177.0 Model 177.1/9 Liftgate/trunk lid to side wall	*BE60.00-P-1015-01JA
		Model 177.0 Roof spoiler to roof	*BE60.00-P-1014-01JA
		Model 177.0 Roof spoiler to side wall	*BE60.00-P-1013-01JA
		Model 177.0 Model 177.1/9 Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	*BE60.00-P-1012-01JA
		Model 177.0 Model 177.1/9 Rear door to side wall	*BE60.00-P-1011-01JA
		Model 177.0 Model 177.1/9 Front door cover to rear door cover (B-pillar)	*BE60.00-P-1010-01JA
		Model 177.0 Model 177.1/9 Front door to rear door	*BE60.00-P-1009-01JA
		Model 177.0 Model 177.1/9 Front door to fender	*BE60.00-P-1008-01JA
		Model 177.0 Model 177.1/9 Fender to side wall (A-pillar)	*BE60.00-P-1007-01JA
		Model 177.0 Model 177.1/9 Fender to bumper at front	*BE60.00-P-1006-01JA
		Model 177.0 Model 177.1/9 Headlamp to fender	*BE60.00-P-1005-01JA
		Model 177.0 Model 177.1/9 Headlamp bottom to bumper	*BE60.00-P-1004-01JA
		Model 177.0 Model 177.1/9 Headlamp front to bumper	*BE60.00-P-1003-01JA
		Model 177.0 Model 177.1/9 Engine hood to fender	*BE60.00-P-1002-01JA
		Model 177.0 Model 177.1/9 Engine hood to bumper	*BE60.00-P-1001-01JA
		Feeler gauge	Fig 1
4	Check all visible parts of vehicle underside for damage and leaks.
			AP00.20-P-0054N
5	Check tires for damage and condition.
			AP40.10-P-4051EW
6	Check disk wheels for damage and condition.
7	Perform chassis alignment.	If required.	AR40.20-P-0200MFA
8	Install remaining parts.	If required.

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1001-01JA	Engine hood to bumper	Dimension "A"	mm	3 (±1)	3 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1001-01MA	Engine hood to bumper	Dimension "A"	mm	3 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1001-01NA	Engine hood to bumper	Dimension "A"	mm	3 (±1)	3 (±1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1002-01JA	Engine hood to bumper	Dimension "B"	mm	3 (±0, 5)	3 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1002-01MA	Engine hood to bumper	Dimension "B"	mm	3 (±0, 5)
		Dimension "B1"	mm	-
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1002-01NA	Engine hood to bumper	Dimension "B"	mm	3 (±0, 5)	3 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1003-01JA	Headlamp front to bumper	Dimension "C"	mm	2 (±1, 5)	2 (±1, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1003-01MA	Headlamp front to bumper	Dimension "C"	mm	2 (±1, 5)
		Dimension "C1"	mm	-
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1003-01NA	Headlamp top to bumper	Dimension "C1"	mm	2.5 (-05/+1.5)	2.5 (-05/+1.5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1004-01JA	Headlamp bottom to bumper	Dimension "D"	mm	2 (±1)	2 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1004-01MA	Headlamp bottom to bumper	Dimension "D"	mm	2 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1004-01NA	Headlamp front to bumper	Dimension "C2"	mm	2, 0 (±1, 5)	2, 0 (±1, 5)

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1005-01JA	Headlamp to fender	Dimension "E"	mm	2 (±1)	2 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1005-01MA	Headlamp to fender	Dimension "E"	mm	2 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1005-01NA	Headlamp bottom to bumper	Dimension "C3"	mm	1, 5 (±1)	1, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1006-01JA	Fender to bumper at front	Dimension "F"	mm	0 (+0, 5)	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1006-01MA	Fender to bumper at front	Dimension "F"	mm	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1006-01NA	Headlamp to fender	Dimension "D"	mm	2 (±1)	2 (±1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1007-01JA	Fender to side wall (A-pillar)	Dimension "G"	mm	2 (+1/-0, 5)	2 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1007-01MA	Fender to side wall (A-pillar)	Dimension "G"	mm	2 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1007-01NA	Fender to bumper at front	Dimension "E"	mm	0 (+0, 5)	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1008-01JA	Front door to fender	Dimension "H"	mm	4 (±0, 5)	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1008-01MA	Front door to fender	Dimension "H"	mm	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1008-01NA	Fender to side wall (A-pillar)	Dimension "F"	mm	2 (-0, 5/+1)	2 (-0, 5/+1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1009-01JA	Front door to rear door	Dimension "I"	mm	4 (±0, 5)	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1009-01MA	Front door to rear door	Dimension "I"	mm	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1009-01NA	Front door to fender	Dimension "G"	mm	4 (±0, 5)	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1010-01JA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (±1)	4 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1010-01MA	Front door cover to rear door cover (B-pillar)	Dimension "J"	mm	4 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1010-01NA	Front door to rear door	Dimension "H"	mm	4 (±0, 5)	4 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1011-01JA	Rear door to side wall	Dimension "K"	mm	3 (+0, 5)	3 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1011-01MA	Rear door to side wall	Dimension "K"	mm	3, 5 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1011-01NA	Rear door to side wall	Dimension "I"	mm	3, 5 (±0, 5)	3, 5 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1012-01JA	Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	Dimension "L"	mm	2 (±0, 5)	2 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1012-01MA	Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	Dimension "L"	mm	2 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1012-01NA	Fuel filler flap/fuel filler flap hybrid to side wall (circumferential)	Dimension "J"	mm	2 (±0, 5)	2 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0
BE60.00-P-1013-01JA	Roof spoiler to side wall	Dimension "M"	mm	4, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1013-01MA	Roof spoiler to side wall	Dimension "M"	mm	4, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1013-01NA	Roof spoiler to side wall	Dimension "K"	mm	-	4, 5 (±1)

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0
BE60.00-P-1014-01JA	Roof spoiler to roof	Dimension "N"	mm	5, 5 (±1, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1014-01MA	Roof spoiler to roof	Dimension "N"	mm	5, 5 (±1, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1014-01NA	Roof spoiler to roof	Dimension "L"	mm	-	4, 5 (-1/+1, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1015-01JA	Liftgate/trunk lid to side wall	Dimension "O"	mm	4, 5 (±1)	3 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1015-01MA	Liftgate/trunk lid to side wall	Dimension "O"	mm	4, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1015-01NA	Liftgate/trunk lid to side wall	Dimension "M"	mm	3, 5 (±1)	3, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1016-01JA	Liftgate/trunk lid to bumper at rear	Dimension "P"	mm	5, 5 (±1, 5)	5, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1016-01MA	Liftgate/trunk lid to bumper at rear	Dimension "P"	mm	6 (±2)
		Dimension "P1"	mm	-
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1016-01NA	Liftgate/trunk lid to bumper at rear	Dimension "N"	mm	6 (±1)	6 (±1, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1017-01JA	Outer tail lamp to side wall	Dimension "Q"	mm	1 (+1/-0, 5)	1 (+1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1017-01MA	Outer tail lamp to side wall	Dimension "Q"	mm	1, 5 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1017-01NA	Outer tail lamp to side wall	Dimension "O"	mm	1, 5 (±0, 5)	1, 5 (±0, 5)

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1018-01JA	Outer tail lamp to bumper at rear	Dimension "R"	mm	2 (±1)	1, 5 (+1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1018-01MA	Outer tail lamp to bumper at rear	Dimension "R"	mm	2 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1018-01NA	Outer tail lamp to bumper at rear	Dimension "P"	mm	1, 5 (+1)	1, 5 (+1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0
BE60.00-P-1019-01JA	Outer tail lamp to liftgate	Dimension "S"	mm	3, 5 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1019-01MA	Outer tail lamp to liftgate	Dimension "S"	mm	3, 5 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1019-01NA	Outside of taillamp to inside of taillamp	Dimension "Q"	mm	3, 5 (-0.5/+1)	3, 5 (-0.5/+1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1020-01JA	Outside of taillamp to inside of taillamp	Dimension "T"	mm	3, 5 (+1/-0, 5)	3, 5 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1020-01MA	Outer tail lamp to inner tail lamp/rear continuous reflector strip	Dimension "T"	mm	3, 5 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1020-01NA	Liftgate/trunk lid to inner tail lamp (top)	Dimension "R"	mm	1 (±0, 5)	1 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1021-01JA	Liftgate/trunk lid to inner tail lamp (top)	Dimension "U"	mm	1 (±0, 5)	1 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1021-01MA	Tailgate/trunk lid to inner tail lamp (top)/rear continuous reflector strip (top)	Dimension "U"	mm	1 (±0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1021-01NA	Liftgate/trunk lid to inner tail lamp (bottom)	Dimension "S"	mm	1, 5 (-0, 5/+1)	1, 5 (-0, 5/+1)

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1022-01JA	Liftgate/trunk lid to inner tail lamp (bottom)	Dimension "V"	mm	2, 5 (±1)	1, 5 (+1/-0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1022-01MA	Tailgate/trunk lid to inner tail lamp (bottom)/rear continuous reflector strip (bottom)	Dimension "V"	mm	2, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1022-01NA	Bumper at rear to side wall	Dimension "T"	mm	0 (+0, 5)	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1023-01JA	Bumper at rear to side wall	Dimension "W"	mm	0 (+0, 5)	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1023-01MA	Bumper at rear to side wall	Dimension "W"	mm	0 (+0, 5)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1023-01NA	Trunk lid to rear window	Dimension "U"	mm	7, 0 (± 2, 0)	-
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.1/9
BE60.00-P-1024-01JA	Trunk lid to rear window	Dimension "X"	mm	8, 5 (±2)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 247.0
BE60.00-P-1024-01MA	Trunk lid to rear window	Dimension "X"	mm	4, 5 (±1)
		For picture, see		AR60.00-P-0700-01MFA

GAP DIMENSIONS

Number	Designation			Model 118.3	Model 118.6
BE60.00-P-1024-01NA	Longitudinal member panel to front door/rear door	Dimension "V"	mm	5 (±1)	5 (±1)
		For picture, see		AR60.00-P-0700-01MFC	AR60.00-P-0700-01MFC

TEST AND ADJUSTMENT VALUES FOR GAP DIMENSIONS

Number	Designation			Model 177.0	Model 177.1/9
BE60.00-P-1025-01JA	Trunk lid to rear window/front door/rear door	Dimension "Y"	mm	5 (±1)	5 (±1)
		For picture, see		AR60.00-P-0700-01MFA	AR60.00-P-0700-01MFA

GAP DIMENSIONS 

Number	Designation			Model 247.0
BE60.00-P-1025-01MA	Longitudinal member panel to front door/rear door	Dimension "Y"	mm	5, 0 (±1)
		For picture, see		AR60.00-P-0700-01MFA

Fig 1: Identifying Feeler Gauge (129 589 03 21 00)

Courtesy of MERCEDES-BENZ USA