Remove/Install Wiper Arm - AR82.30-P-6100S
Model 223
Shown with code 874 (MAGIC VISION CONTROL, heated)
| Risk of fire and explosion caused by ignition of window washing fluid or antifreeze and their vapors. Risk of poisoning caused by swallowing window washing fluid or antifreeze or inhaling their vapors. Risk of injury or physical irritations caused by contact of window washing fluid or antifreeze with eyes, mucous membranes or skin. | Wear protective clothing and tight-fitting safety glasses. No open flames, fire or ignition sources. Avoid contact with eyes, mucous membranes and skin. When working with window washing fluids or antifreeze, do not eat, drink, or smoke. Do not inhale vapors and ensure sufficient ventilation in the working area. Store window | AS82.35-Z-0001-01A | |
| washing fluid and antifreeze leakfree in safely closed original containers and out of the reach of children. | |||
| Injury hazard from pinching and crushing, in extreme cases extremities can even be cut off when caught in windshield wiper mechanism. | When working on the windshield wiper mechanism, always switch off the ignition and store transmitter key outside of transmission range (at least 2 m). | AS82.30-Z-0001-01A | |
| Notice | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Remove | |||
| 1 | Move windshield wiper system to park position. | ||
| 2 | Switch off ignition and store transmitter key outside of transmitter range (min. 2 m). | ||
| 3 | Open hood. | ||
| 4 | Remove covers (1). | ||
| 5 | Release and disconnect electrical connection (9). | ||
| 6 | Disconnect hose coupling (8, 10). | ||
| 7 | Detach covers (4, 5) and remove nuts located underneath. | *BA82.30-P-1002-01P | |
| 8 | Unclip hoses (2, 3) and electrical wiring harnesses of heated wiper arms (6, 7) from respective mounting clamps and route through opening in air/water duct. | Model 223 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system) |
|
| 9 | Take off wiper arms (6, 7) or remove using puller. | ||
| Fig 2 | |||
| Fig 1 | |||
| Installation of wiper arm (6) on driver's side | |||
| 10 | Connect diagnostic system. | ||
| AD00.00-P-2000-06FR | |||
| 11 | Switch on ignition. | ||
| 12 | Set wiper motor to upper position using vehicle diagnosis system. | ||
| AD00.00-P-2000-06FR | |||
| 13 | Mount wiper arm (6) on drive spigot and align parallel to A-pillar. | *BE82.30-P-1005-01M | |
| 14 | Attach nut (4) of wiper arm (6). | *BA82.30-P-1002-01P | |
| 15 | Move wiper arm (6) to parked position using diagnostic system and then move back to upper position. | ||
| AD00.00-P-2000-06FR | |||
| 16 | Raise wiper arm (6) and lower it again. | Measurement errors occur otherwise. |
|
| 17 | Check distance of wiper arm (6) to A-pillar. | *BE82.30-P-1005-01M | |
| If the measurement value is outside the tolerance range, replace wiper arm (6) and start again at operation step 13. | |||
| 18 | Move wiper arm (6) to parked position using diagnostic system. | ||
| AD00.00-P-2000-06FR | |||
| Installation of wiper arm (7) on front passenger side | |||
| 19 | Mount wiper arm (7) on drive spigot and align with marking on windshield. | ||
| 20 | Attach nut (4) of wiper arm (7). | *BA82.30-P-1002-01P | |
| Install | |||
| 21 | Switch on ignition. | ||
| 22.1 | Perform trial run of wiper arms (6, 7) using diagnostic system. | If both wiper arms (6, 7) or only wiper arm (6) were/was removed. | |
| AD00.00-P-2000-06FR | |||
| 22.2 | Perform trial run of wiper arms (6, 7) without diagnostic system. | If wiper arm (7) on front passenger side was removed. | |
| 23 | Disconnect vehicle diagnosis system from vehicle. | If both wiper arms (6, 7) or only wiper arm (6) were/was removed. | |
| AD00.00-P-2000-06FR | |||
| 24 | Guide hoses (2, 3) and electrical wiring harnesses of wiper arms (6, 7) through opening in air/water duct and clip into respective mounting clamps. | Model 223 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system) |
|
| 25 | Connect hose coupling (8, 10). | ||
| 26 | Connect electrical connector (9). | ||
| 27 | Attach covers (4, 5). | ||
| 28 | Attach covers (1). | ||
| Check | |||
| 29 | Perform function check on windshield wiper system. | ||
| AP82.35-P-8252J |
TEST AND ADJUSTMENT VALUES FOR WIPER ARMS
| Number | Designation | Model 223 except code 874 (MAGIC VISION CONTROL incl. heated windshield washer system) | Model 223 with code 874 (MAGIC VISION CONTROL incl. heated windshield washer system) | |
|---|---|---|---|---|
| BE82.30-P-1005-01M | Distance of driver-side wiper arm in the upper position to A-pillar | mm | 25 (±5) | 25 (±5) |
WINDSHIELD WIPER
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BA82.30-P-1002-01P | Nut, wiper arm to windshield wiper system | M10 | Nm | 30 |