Remove/Install Front Pre-Fuse Box - AR54.15-P-1330S
Model 223
Shown on model 223.### 1# with code ME10 (Hybrid vehicle)
Fig 1: Front Pre-Fuse Box Components Location - Model 223 (Shown On Model 223.### 1# With Code ME10)
Shown on model 223.### 1# with code ME10 (Hybrid vehicle)
| Notice | Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | |
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Remove/install | |||
| 1 | Disconnect ground line of 12 V on-board electrical system battery. | AR54.10-P-0051S | |
| 2.1 | Remove cover (1) in right engine compartment. | Model 223.### 1# | |
| 2.2 | Remove cover (1) in left engine compartment. | Model 223.### 2# | |
| 3 | Remove wiper arms. | AR82.30-P-6100S | |
| 4 | Remove water drain (2). | ||
| 5 | Unclip air quality sensor (B31) with electric line from air intake scoop (3) and place to one side. | ||
| 6 | Unclip air intake scoop (3) and remove. | ||
| 7 | Remove upper strut (4). | *BA62.30-P-1007-02P | |
| *BA62.30-P-1002-02P | |||
| 8 | Remove center strut (5). j | *BA62.30-P-1009-02P | |
| *BA62.30-P-1008-02P | |||
| 9.1 | Remove battery of 48 V on-board electrical system. | Model 223 with engine 176 with code B01 (48V technology) Model 223 with engine 256 with code B01 (48V technology) Model 223 with engine 656 with code B01 (48V technology) |
|
| AR54.10-P-0022S | |||
| 9.2 | Remove battery of 12 V on-board electrical system. | Model 223 with engine 177 with code B01 (48V technology) with code ME10 (Hybrid vehicle (plug-in, PHEV)) |
|
| AR54.10-P-1134SA | |||
| 10 | Release and disconnect electrical connector (6) of pyrofuse from engine compartment pre-fuse box (F150/3). | Model 223 with code ME10 (Hybrid vehicle (plug-in, PHEV)) |
|
| 11 | Remove cap (7) at top from engine compartment pre-fuse box (F150/3). | ||
| 12 | Remove electric lines (8) at top from engine compartment pre-fuse box (F150/3). | The connections of the electric lines (8) are shape-coded. |
|
| *BA54.15-P-1002-01J | |||
| 13 | Release and disconnect electrical connection (9). | Model 223 with code ME10 (Hybrid vehicle (plug-in, PHEV)) |
|
| 14 | Remove cap (10) at side from engine compartment pre-fuse box (F150/3). | ||
| 15 | Remove electric lines (11) at side from engine compartment pre-fuse box (F150/3). | The connections of the electric lines (11) are shape-coded. |
|
| *BA54.15-P-1002-01J | |||
| 16 | Remove bolts (12) and remove nut (13). | *BA54.15-P-1001-01J | |
| 17 | Remove engine compartment pre-fuse box (F150/3). | ||
| 18 | Install in the reverse order. |
FUSE AND RELAY BOX
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BA54.15-P-1001-01J | Nut/screw, engine compartment pre-fuse box to body | M6 | Nm | 4 |
FUSE AND RELAY BOX
| Number | Designation | Model 223 | ||
|---|---|---|---|---|
| BA54.15-P-1002-01J | Nut, positive terminal to engine compartment pre-fuse box | M6 | Nm | 8 |
| M8 | Nm | 16 | ||
FRONT AREA WITH FRONT REINFORCEMENT
| Number | Designation | Model 223 | |
|---|---|---|---|
| BA62.30-P-1002-02P | Screw, upper/lower struts to firewall | Nm | 30 |
FRONT AREA WITH FRONT REINFORCEMENT
| Number | Designation | Model 223 | |
|---|---|---|---|
| BA62.30-P-1007-02P | Screw, upper strut on suspension strut tower mounting console | Nm | 30 |
FRONT AREA WITH FRONT REINFORCEMENT
| Number | Designation | Model 223 | |||
|---|---|---|---|---|---|
| BA62.30-P-1008-02P | Screw, center/lower strut to suspension strut tower mounting console | Stage 1 | Nm | 35 | |
| Stage 2 | Nm | 50 | |||
| Stage 3 | Loosen | ∠° | 180 | ||
| Stage 4 | Nm | 50 | |||
FRONT AREA WITH FRONT REINFORCEMENT
| Number | Designation | Model 223 | |
|---|---|---|---|
| BA62.30-P-1009-02P | Screw, center strut to longitudinal member mounting console | Nm | 30 |