Remove/Install Folding Rear Seat - AR91.12-P-1720LW
WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2023 Mercedes-Benz C43 AMG, 2022 Mercedes-Benz C43 AMG, 2021 Mercedes-Benz C43 AMG, 2020 Mercedes-Benz C43 AMG, and 2019 Mercedes-Benz C43 AMG. However, it is still accessible from the selected car via links, so may be relevant.
Model 205.0/1, 213.0
with code 287 (Folding seat backrests in rear passenger compartment)
Model 205.2/3
Model 213.2
Model 253 (except 253.992/993), 293
Shown on model 205.1 with code 872 (Seat heating in rear passenger compartment)
| Remove/install | |||
| 1.1 | Remove left and right seat side bolster. | Model 205.0/1, 213.0 with code 287 (Folding seat backrests in rear passenger compartment) Model 205.2/3 Model 213.2 Model 205.0/1, 213.0 with code 287 (Folding seat backrests in rear passenger compartment) |
|
| Model 205.2/3 | AR91.12-P-1710LW | ||
| Model 213.2 | AR91.12-P-1711LWT | ||
| 1.2 | Remove rear passenger compartment seat cushion. | Model 253 (except 253.992/993), 293 | AR91.12-P-1020LW |
| 2 | Move driver seat and front passenger seat to foremost position. | ||
| 3 | Disconnect and unclip electrical connector of rear passenger compartment seat backrest heater pad (X54/39, X54/40). | Model 205.1, 213.0 with code 287 (Folding seat backrests in rear passenger compartment) with code 872 (Heated rear seats) Model 213.2, 253 (except 253.992/993), 293 with code 872 (Heated rear seats) |
|
| 4 | Release right seat backrest (1), center seat backrest (2) and left seat backrest (3) and fold forward. | ||
| 5 | Disconnect electrical connector at right rear passenger compartment seat backrest inclination switch (S54/6) and take electrical wiring harness out of working area. | ||
| 6 | Disconnect electrical connector for rear passenger compartment seat backrest release actuator (X77/2, X77/1). | Model 205.2, 253 (except 253.992/993), 293 | |
| 7 | Fold back left seat backrest (3). | ||
| 8 | Unscrew bolt (7). | *BA91.12-P-1003-03M | |
| 9 | Remove lock washer (14). | Model 205.2/3, 213.2 Model 253 (except 253.992/993), 293 |
|
| 10 | Pull right seat backrest (1) off center seat backrest (2) and remove. | Do not tilt right backrest (1). Otherwise, the spacer ring in the right seat backrest (1) may be damaged. |
|
| 11 | Remove screws (9) at pivot bearing (10) of center seat backrest (2). | The pivot bearing (10) is only connected with one screw/bolt (9) at the crossbar. |
*BA91.12-P-1004-03M |
| 12 | Guide pivot bearing (10) out of crossbar and from center seat backrest (2) at same time. | Model 253.953/954 Do not tilt pivot bearing (10). Otherwise, the spacer ring (11) in the pivot bearing (10) may be damaged. |
|
| 13 | Detach center seat backrest (2) from left seat backrest (3) and remove. | Do not tilt center seat backrest (2). Otherwise the spacer ring in the center seat backrest (2) could be damaged. |
|
| 14 | Remove screw (6), place left seat belt buckle (5) to one side and guide seat belt end fitting (4) upward. | Model 205.0/1, 213.0 with code 287 (Folding seat backrests in rear passenger compartment) Model 205.2, 213.2, 253 (except 253.992/993), 293 |
*BA91.40-P-1009-01U |
| 15 | Release left seat backrest (3) and fold forwards. | When removing the left seat backrest (3), always start with the right seat backrest (1) and then remove the center seat backrest (2). Otherwise, the spacer ring (11) in the pivot bearing (10) of the left seat backrest (3) may be damaged. |
|
| 16 | Remove screws (9) from pivot bearing (10) of left seat backrest (3). | *BA91.12-P-1004-03M | |
| 17 | Remove bolt (13). | *BA91.12-P-1003-03M | |
| 18 | Remove lock washer (15). | Model 205.2/3, 213.2 Model 253 (except 253.992/993), 293 |
|
| 19 | Disconnect electrical connector at left rear passenger compartment seat backrest inclination switch (S54/5) and take electrical wiring harness out of working area. | ||
| 20 | Remove left seat backrest (3). | Do not tilt the pivot bearings (10, 12). Otherwise, the spacer ring in the left seat backrest (3) and the spacer ring (11) in the pivot bearing (10) may be damaged. |
|
| 21 | Install in the reverse order |
REAR SEATS
| Number | Designation | Model 205.0 | Model 205.1 | |
|---|---|---|---|---|
| BA91.12-P-1003-03M | Bolt, outer pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 205.2 | Model 205.3 | |
|---|---|---|---|---|
| BA91.12-P-1003-03M | Bolt, outer pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 213.0 | Model 213.2 | |
|---|---|---|---|---|
| BA91.12-P-1003-03M | Bolt, outer pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 253 | Model 293 | |
|---|---|---|---|---|
| BA91.12-P-1003-03M | Bolt, outer pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 205.0 | Model 205.1 | |
|---|---|---|---|---|
| BA91.12-P-1004-03M | Bolt, center pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 205.2 | Model 205.3 | |
|---|---|---|---|---|
| BA91.12-P-1004-03M | Bolt, center pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 213.0 | Model 213.2 | |
|---|---|---|---|---|
| BA91.12-P-1004-03M | Bolt, center pivot bearing to body | Nm | 40 | 40 |
REAR SEATS
| Number | Designation | Model 253 | Model 293 | |
|---|---|---|---|---|
| BA91.12-P-1004-03M | Bolt, center pivot bearing to body | Nm | 40 | 40 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 205.0 | Model 205.1 | |
|---|---|---|---|---|
| BA91.40-P-1009-01U | Bolt, rear seat belt buckle | Nm | 35 | 35 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 205.2 | Model 213 | |
|---|---|---|---|---|
| BA91.40-P-1009-01U | Bolt, rear seat belt buckle | Nm | 35 | 35 |
SEAT BELTS/EMERGENCY TENSIONING RETRACTORS
| Number | Designation | Model 253 | Model 293 | |
|---|---|---|---|---|
| BA91.40-P-1009-01U | Bolt, rear seat belt buckle | Nm | 35 | 30 |