Perform Wheel Alignment Check - AR40.20-P-0200AC

Model 460, 461 (except 461.339)

Model 463

up to model year 2019

1	Checking and preparing for wheel alignment		AR40.20-P-0060AC
2	Position front wheels of vehicle on turntables	If using an electronic measuring system with integrated turntables, the measuring system must be approved by Mercedes-Benz.	AR40.20-P-0200-12AC
3	Using the adapter, install the brake pedal retaining tool between the pedal and the driver seat	Adapter for brake pedal winch	Fig 2
		Brake pedal jack	Fig 1
4	Open window on driver's door
5	Switch off ignition
6	Mount universal bracket for measurement pickup onto front and rear wheels		AR40.20-P-0231AC
7	Attach and adjust measurement pickup	Observe the operator's manual for the measuring system at all times.
8	Determine specified value for caster	Fluctuations in axle load for the various models and equipment will cause the caster value to change depending on the vehicle load relative to the spring travel. It is not possible to correct the caster value on the vehicle. The specified caster value is changed only if the trailing arms are bent or the suspension tubes are twisted.	AR40.20-P-0336AC
9	Unlock turntables
10	Perform initial measurement	Observe the operator's manual for the measuring system at all times. Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Difference in wheelbase between left and right sides	*BE40.20-P-1006-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Toe-out on turns with the inside wheel steered through 20°	*BE40.20-P-1005-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Steering axis inclination	*BE40.20-P-1004-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Caster	*BE40.20-P-1003-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Camber	*BE40.20-P-1002-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Toe-in	*BE40.20-P-1001-11A
11	Evaluating measurement results	If the problem no longer exists after evaluation of the measurement results. ↓ End wheel alignment measurement procedure and continue with operation step 14.
12	Adjust front axle toe	According to results of initial measurement. Model 460, 461 (except 461.339) Model 463 as of model year 2013 up to model year 2019	AR40.20-P-0323GG
13	Perform final measurement	Observe the operator's manual for the measuring system at all times. Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Difference in wheelbase between left and right sides	*BE40.20-P-1006-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Toe-out on turns with the inside wheel steered through 20°	*BE40.20-P-1005-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Steering axis inclination	*BE40.20-P-1004-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Caster	*BE40.20-P-1003-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Camber	*BE40.20-P-1002-11A
		Model 460, 461 (except 461.331/339) with front axle 730.3 Model 461.331 with front axle 730.3 Model 463 with front axle 730.3 up to model year 2019Toe-in	*BE40.20-P-1001-11A
14	Remove measurement pickup	Observe the operator's manual for the measuring system at all times.
15	Remove universal bracket for measurement pickup from front and rear wheels		AR40.20-P-0231AC
16	Remove brake pedal jack and adapter	Adapter for brake pedal winch	Fig 2
		Brake pedal jack	Fig 1
17	Lock turntables
18	Drive vehicle off measuring system
19	Check straight-line stability and turn-signal cancellation during a test drive
20	Check headlamp adjustment	Model 460, 461 (except 461.339) Model 463 up to model year 2019	AP82.10-P-8260G