LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2021 >> G63 AMG >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Brakes - Hydraulic & Mechanical System - 463 Chassis (3 Of 4) >> Maintenance >> Replace Brake Fluid >> Replace Brake Fluid - AP42.00-P-4280GA

Replace Brake Fluid - AP42.00-P-4280GA

Model 463 

as of model year 2019 

Shown in model 463.349 

G13668684Courtesy of MERCEDES-BENZ USA
WARNING Risk of injury.  Skin or eye injuries may result when handling hot or glowing objects. Wear protective gloves, protective clothing and safety glasses, if necessary. AS00.00-Z-0002-01A
  Risk of death  caused by vehicle slipping or toppling off of the lifting platform. Align vehicle between vehicle lift columns and position the four support plates at the vehicle lift support points specified by the vehicle manufacturer. AS00.00-Z-0010-01A
CAUTION Risk of poisoning  from swallowing brake fluid. Risk of injury  from skin and eye contact with brake fluid Only pour brake fluid into suitable and appropriately marked containers. Wear protective clothing and eye protection when handling brake fluid. AS42.50-Z-0001-01A
  Risk of accident  when commissioning the vehicle due to a lack of braking effect when the service brake is operated for the first time after repair work. Before starting the engine, actuate brake pedal several times until pressure is built up and maintained in the brake system. AS42.50-Z-0002-01A
  Notes on repairs to brake system   AH42.00-P-0003-01A
  Brake fluid notes   AH42.50-P-0001-01A
CLEANING Clean     
1 Clean area surrounding cap (2) and expansion reservoir (1).    
REMOVING Remove     
2 Unscrew cap (2).    
3 Extract brake fluid from expansion reservoir (1).    
4 Add new brake fluid up to the max. marking in the expansion reservoir (1).    
5 Connect filling and bleeding unit to expansion reservoir (1) and switch on. NOTES
Note operating instructions for filling and bleeding unit.
Damage can otherwise occur.
 
  Change fluid     
6 Lift vehicle with lifting platform.    
REFER TO TESTING & REPAIR     AR00.60-P-1006A
7 Renew brake fluid.    
REFER TO CAPACITIES & SPECIFICATIONS General brake fluid   BB00.40-P-0330-01A
REFER TO CAPACITIES & SPECIFICATIONS Brake fluids (DOT 4 plus)   BB00.40-P-0331-00A
REFER TO TESTING & REPAIR     AR42.10-P-0010-02XG
    NOTES
New brake fluid must escape without any bubbles via the bleed hose.
Damage can otherwise occur.
 
    TORQUE SPECIFICATION Bleed screw at brake caliper *BA42.10-P-1003-10Y 
    TORQUE SPECIFICATION Bleed screw on rear axle floating caliper If the bleed valve is not accessible,
↓
Detach/attach wheel and tire assemblies.
IMPORTANT After obtaining special order.
*BA42.10-P-1001-17B 
INSPECT Check     
8 Check brake system for leaks.    
INSTALLING Install     
9 Lower vehicle with vehicle lift.    
REFER TO TESTING & REPAIR     AR00.60-P-1006A
10 Disconnect filling and bleeding unit.    
INSPECT Check     
11 Check fluid level in expansion reservoir (1).   AP42.10-P-4210GA 
INSTALLING Install     
12 Screw on cap (2).    
REAR AXLE FLOATING CALIPER

Number Designation Model 463 as of model year 2019
BA42.10-P-1001-17B Bleed screw on rear axle floating caliper Nm 11
FRONT AXLE BRAKE CALIPER

Number Designation Model 463
as of model year 2019
BA42.10-P-1003-10Y Bleed screw at brake caliper Nm 16