Remove/Install Front Left Or Right RPM Sensor - AR42.30-P-0712LW
WARNING: This page does not describe the selected car, but rather 23 other vehicles, including the 2023 Mercedes-Benz E63 S AMG, 2023 Mercedes-Benz E53 AMG, 2023 Mercedes-Benz E350, 2022 Mercedes-Benz E53 AMG, and 2022 Mercedes-Benz E350. However, it is still accessible from the selected car via links, so may be relevant.
Model 205
Model 213 (except 213.061/261)
Model 253
Model 293
MODIFICATION NOTES
| 10.11.2020 | "Screw, rotational speed sensor to steering knuckle" added. | Operation step 3. |
Shown on model 205
Shown on model 213
Fig 1: Front Left /Right RPM/Wheel Speed Sensor Components Location - Model 213 (except 213.061/261)
| Notes on self-locking nuts and bolts | AH00.00-N-0001-01A | ||
| Notes on handling, transport and storage of | AH42.10-P-9406-12LF | ||
| composite brake disks | |||
| Notes on handling, transport and storage of ceramic brake disks | AH42.10-P-9406-13A | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Notes on safety-relevant components | AH00.00-Z-0019-01A | ||
| Remove/install | |||
| 1 | Remove front wheel. | AR40.10-P-1102A | |
| 2 | Release and disconnect electrical connector (12). | Model 213 (except 213.061/261) Model 253.388/389/988/989 |
|
| 3 | Remove screw (1). | *BA42.30-P-1001-01K | |
| 4 | Lift holder (2) over nut (arrow) and detach left front axle rpm sensor (L6/1) or right front axle rpm sensor (L6/2). | Model 205, 253 (except 253.388/389/988/989) | |
| 5 | Route electric line (3) out of holder (2) and let holder (2) hang down at the side. | Model 205, 253 (except 253.388/389/988/989) | |
| 6 | Release and disconnect electrical plug (5) from level sensor. | Model 205, 253, 293 If installed. | |
| 7 | Unclip holder (7) on upper transverse control arm (6) and swing connecting linkage (8) upwards with lever (9). | Model 205, 253, 293 If installed. | |
| 8 | Fix holder (7) in place on upper transverse control arm (6) with cable tie. | Model 205, 253, 293 If installed. | |
| 9 | Disconnect electrical connector (10) from front axle right distributor electrical connector (X62/6) or front axle left distributor electrical connector (X62/7). | Model 205, 253, 293 | |
| 10 | Remove nut (11) of fender interior trim, open holder (4), and remove and expose electric line (3) from holder (4). | Model 205, 253 | |
| 11 | Remove left front axle rotational speed sensor (L6/1) or right front axle rotational speed sensor (L6/2). | ||
| 12 | Install in the reverse order. | ||
| 13 | Read out and erase fault memory using the vehicle diagnosis system. | ||
| Model 293 | AD00.00-P-2000-06FR | ||
| Model 205, 253 Model 213 (except 213.061/261) |
AD00.00-P-2000-04B |
FRONT AXLE RPM SENSOR
| Number | Designation | Model 205 | Model 213 | ||
|---|---|---|---|---|---|
| BA42.30-P-1001-01K | Bolt, rpm sensor to steering knuckle | M6 | Nm | 8 | 8 |
FRONT AXLE RPM SENSOR
| Number | Designation | Model 253 | Model 293 | ||
|---|---|---|---|---|---|
| BA42.30-P-1001-01K | Bolt, rpm sensor to steering knuckle | M6 | Nm | 8 | 8 |