Retrofit CD Drive - AZ82.64-P-0002RFC

Model 257 

with code 531 (COMAND APS) 

except code 320 (Single CD drive preinstallation) 

except code 460 (Canada version) 

except code 494 (US version) 

except code 498 (Japanese version) 

except code 830 (China version) 

Courtesy of MERCEDES-BENZ USA

Topical note	Notes on the use of paint scraping nuts on ground connections		AH00.19-P-1000-20A
Topical note	Information on preventing damage to electronic components due to electrostatic discharge		AH54.00-P-0001-01A
	Remove
1	Remove fragrance generator.	Model 257 with code 531 (COMAND APS) with code P21 (Air quality package) except code 320 (Single CD drive preinstallation) except code 460 (Canada version) except code 494 (US version) except code 498 (Japanese version) except code 830 (China version)
2	Remove glove compartment housing.
			AR68.10-P-1402FR
3	Remove head unit.
			AR82.85-P-1101FR
4	Detach HERMES control unit with holder and place to one side with lines attached.
			AR82.95-P-0019FR
5	Remove COMAND display.
			AR82.85-P-7429FR
6	Remove trim at bottom for instrument panel on driver's side.
			AR68.10-P-1501FR
7	Release fuse and relay module on driver's side (K40/6).
	Assignment of driver-side fuse and relay module		GF54.15-P-1256-49FR
		so that electrical fuse 204 (K40/6f204) is accessible.	AR54.15-P-0003FR
8	Remove door sill on driver's side.
	Install
9	Prepare holder drilling template for CD drive (1).	Model 257.### 1# with code 531 (COMAND APS) except code 320 (Single CD drive preinstallation) except code 460 (Canada version) except code 494 (US version) except code 498 (Japanese version) except code 830 (China version)	AZ82.64-P-0002-04LWE
		Model 257.### 2# with code 531 (COMAND APS) except code 320 (Single CD drive preinstallation) except code 460 (Canada version) except code 494 (US version) except code 498 (Japanese version) except code 830 (China version)	AZ82.64-P-0002-04LWR
10	Prepare adhesive film cutting template for CD drive (1).		AZ82.64-P-0002-05LWE
11	Cut adhesive film to size using cutting template.
12	Prepare glove compartment housing for installation of CD drive (1).	Model 257.### 1# with code 531 (COMAND APS) except code 320 (Single CD drive preinstallation) except code 460 (Canada version) except code 494 (US version) except code 498 (Japanese version) except code 830 (China version)	AZ82.64-P-0002-08LWE
		Model 257.### 2# with code 531 (COMAND APS) except code 320 (Single CD drive preinstallation) except code 460 (Canada version) except code 494 (US version) except code 498 (Japanese version) except code 830 (China version)	AZ82.64-P-0002-08LWR
13	Prepare holder for CD drive (1) for installation.		AZ82.64-P-0002-06LWE
14	Retrofit wiring harness for CD drive (1).		AZ82.64-P-0002-01LWE
		Left footwell ground point	*BA00.19-P-1021-02D
15	Retrofit CD drive (1) into glove compartment housing.		AZ82.64-P-0002-03LWE
16	Install glove compartment housing with CD drive (1).
		Pay attention to installation of lines.	AR68.10-P-1402FR
17	Insert 5 A fuse into slot f204 of fuse and relay module on driver's side (K40/6).
	Assignment of driver-side fuse and relay module		GF54.15-P-1256-49FR
18	Install remaining parts.
	Update Vehicle Documentation (VeDoc)
19	Enter special equipment into online vehicle data card.	Code 320 (Single CD drive pre-installation)
20	Attach "CD drive retrofitted as per AZ82.64-P-0002RFC" note under field organization texts.	On design group 82 and design group 54.
21	Connect diagnostic system and select vehicle using vehicle identification number (VIN).
			AD00.00-P-2000-06FR
22	Perform variant coding using the software calibration number (SCN).	Head unit
23	Disconnect diagnostic system.
			AD00.00-P-2000-06FR
	Check
24	Perform function test.	See Owner's Manual.