Remove/Install Headlamp Unit - AR82.10-P-4730LW
WARNING: This page is about a different car, the 2023 Mercedes-Benz GLC300, 2022 Mercedes-Benz GLC300, 2021 Mercedes-Benz GLC300, 2020 Mercedes-Benz GLC350e, and 2020 Mercedes-Benz GLC300. However, it is still accessible from the selected car via links, so may be relevant.
Model 205, 213, 253, 293
Shown on model 205 on left side of vehicle
Shown on model 205 on left side of vehicle
| Note on damage to lamp unit | AH82.10-P-0002-00LW | ||
| Information on preventing damage to electronic components due to electrostatic discharge | AH54.00-P-0001-01A | ||
| Remove | |||
| 1 | Perform initial startup of the left front lamp unit (E1) or right front lamp unit (E2) with diagnostic system. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 293 | AD00.00-P-2000-06FR | ||
| Model 205, 213, 253 with code 631 (Static LED headlamps, left-hand traffic) | AD00.00-P-2000-04B | ||
| Model 205, 213, 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 205, 253 with code 640 (High-performance LED) Model 205, 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205, 253 with code 642 (Dynamic LED headlamps, right-hand traffic) Model 213 with code P35 (Light Package) |
|||
| 2 | Switch off ignition and store transmitter key outside of transmission range (min. 2 m). | ||
| 3.1 | Undo bumper in area of left front lamp unit (E1) or right front lamp unit (E2). | When removing left front lamp unit (E1) or right front lamp unit (E2). | |
| Model 205, 253, 293 | AR88.20-P-2000LW | ||
| Model 213 | AR88.20-P-2000LWE | ||
| 3.2 | Remove front bumper. | When removing left front lamp unit (E1) and right front lamp unit (E2). | |
| Model 205, 253, 293 | AR88.20-P-2000LW | ||
| Model 213 | AR88.20-P-2000LWE | ||
| 4 | Remove screws (1, 2, 3). | ||
| 5 | Use tape to mask off left front lamp unit (E1) or right front lamp unit (E2) in area of fender. | If a new left front lamp unit (E1) or right front lamp unit (E2) is not installed. | |
| 6 | Remove left front lamp unit (E1) or right front lamp unit (E2) far enough to gain access to the electrical connector (4). | ||
| 7 | Disconnect electrical connector (4) from left front lamp unit (E1) or right front lamp unit (E2). | ||
| 8 | Remove left front lamp unit (E1) or right front lamp unit (E2). | ||
| 9 | Remove front lamp unit LED module. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 293 | AR82.10-P-4656EQ | ||
| Model 205, 253 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4656LW | ||
| Model 205, 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 205, 253 with code 640 (High-performance LED) Model 205, 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205, 253 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| 10 | Remove front actuation module, LED exterior lighting. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 205 with code 640 (High-performance LED) | AR82.10-P-4650LW | ||
| Model 205 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| Model 253 with code 640 (High-performance LED) | AR82.10-P-4650LWG | ||
| Model 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 253 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| 11 | Remove headlamp control unit. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 205 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4660LW | ||
| Model 205 with code 632 (Headlamps, LED, static, right-side traffic) Model 205 with code 640 (High-performance LED) Model 205 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| Model 213 with code P35 (Light Package) except code 631 (Static LED headlamps, left-hand traffic) except code 632 (Headlamps, LED, static, right-side traffic) |
AR82.10-P-4660LWE | ||
| Model 213 with code 631 (Static LED headlamps, left-hand traffic) except code P35 (Light Package) | AR82.10-P-4660LWF | ||
| Model 213 with code 632 (Headlamps, LED, static, right-side traffic) except code P35 (Light Package) | |||
| Model 253 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4660LWG | ||
| Model 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 253 with code 640 (High-performance LED) Model 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 253 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| 12 | Remove front LED matrix lamp unit control unit. | Model 293 When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 213 with code P35 (Light Package) | AR82.10-P-2025LWE | ||
| Install | |||
| 13 | Install front LED matrix lamp unit control unit. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 213 with code P35 (Light Package) | AR82.10-P-2025LWE | ||
| 14 | Install headlamp control unit. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). |
|
| Model 205 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4660LW | ||
| Model 205 with code 632 (Headlamps, LED, static, right-side traffic) Model 205 with code 640 (High-performance LED) Model 205 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| Model 213 with code P35 (Light Package) except code 631 (Static LED headlamps, left-hand traffic) except code 632 (Headlamps, LED, static, right-side traffic) |
AR82.10-P-4660LWE | ||
| Model 213 with code 631 (Static LED headlamps, left-hand traffic) except code P35 (Light Package) | AR82.10-P-4660LWF | ||
| Model 213 with code 632 (Headlamps, LED, static, right-side traffic) except code P35 (Light Package) | |||
| Model 253 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4660LWG | ||
| Model 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 253 with code 640 (High-performance LED) Model 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 253 with code 642 (Dynamic LED headlamps, right-hand traffic) Model 293 |
|||
| 15 | Install front actuation module, LED exterior lighting. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 205 with code 640 (High-performance LED) | AR82.10-P-4650LW | ||
| Model 205 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| Model 253 with code 640 (High-performance LED) | AR82.10-P-4650LWG | ||
| Model 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 253 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| 16 | Install front lamp unit LED module. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 293 | AR82.10-P-4656EQ | ||
| Model 205, 253 with code 631 (Static LED headlamps, left-hand traffic) | AR82.10-P-4656LW | ||
| Model 205, 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 205, 253 with code 640 (High-performance LED) Model 205, 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205, 253 with code 642 (Dynamic LED headlamps, right-hand traffic) |
|||
| 17 | Use tape to mask off new left front lamp unit (E1) or right front lamp unit (E2) in area of fender. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| 18 | Establish contact for electrical connector (4) on left front lamp unit (E1) or right front lamp unit (E2). | ||
| 19 | Insert left front lamp unit (E1) or right front lamp unit (E2). | ||
| 20 | Screw in screws (1, 2, 3) and tighten gently by hand. | ||
| 21.1 | Install front bumper. | When installing left front lamp unit (E1) and right front lamp unit (E2). | |
| Model 205, 253, 293 | AR88.20-P-2000LW | ||
| Model 213 | AR88.20-P-2000LWE | ||
| 21.2 | Fasten bumper in area of left front lamp unit (E1) or right front lamp unit (E2). | When installing left front lamp unit (E1) or right front lamp unit (E2). | |
| Model 205, 253, 293 | AR88.20-P-2000LW | ||
| Model 213 | AR88.20-P-2000LWE | ||
| 22 | Open maintenance flap in left front or right front fender liner. | ||
| 23 | Align left front lamp unit (E1) or right front lamp unit (E2) and tighten screws (1, 2, 3). | ||
| 24 | Close maintenance flap in left front or right front fender liner. | ||
| 25 | Remove tape from left front lamp unit (E1) or right front lamp unit (E2). | ||
| 26 | Perform initial startup of the left front lamp unit (E1) or right front lamp unit (E2) with diagnostic system. | When replacing the left front lamp unit (E1) or the right front lamp unit (E2). | |
| Model 205, 213, 253 with code 631 (Static LED headlamps, left-hand traffic) | AD00.00-P-2000-04B | ||
| Model 205, 213, 253 with code 632 (Headlamps, LED, static, right-side traffic) Model 205, 253 with code 640 (High-performance LED) Model 205, 253 with code 641 (Dynamic LED headlamps, left-hand traffic) Model 205, 253 with code 642 (LED Intelligent Light System) Model 213 with code P35 (Light Package) |
|||
| Model 293 | AD00.00-P-2000-06FR | ||
| Check | |||
| 27 | Check and correct the headlamp adjustment. | ||
| Model 293 | AP82.10-P-8260KA | ||
| Model 205, 253 | AP82.10-P-8260E | ||
| Model 213 | AP82.10-P-8260J |