LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2019 >> C300 4Matic, 2D Convertible >> Repair and Diagnosis >> Accessories & Equipment >> Collision/Avoidance >> Electrical System, Equipment & Instruments - 205 Chassis 3 Of 6 >> Testing & Repair >> Remove/Install Reversing/Backup Camera >> Remove/Install Reversing/Backup Camera - AR54.65-P-0030LWR

Remove/Install Reversing/Backup Camera - AR54.65-P-0030LWR

Model 205.3/4 

with code 218 (Rear view camera) 

Model 205.3/4 

with code 501 (360° camera) 

Fig 1: Reversing/Backup Camera Components Location - Model 205.3/4 With Codes 218 And 501
G14201386Courtesy of MERCEDES-BENZ USA
G14201387Courtesy of MERCEDES-BENZ USA
G14201388Courtesy of MERCEDES-BENZ USA
G14201389Courtesy of MERCEDES-BENZ USA
WARNING Risk of injury  caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof. No parts of the body or limbs should be within the operating area when the components are moving. AS00.00-Z-0011-01A
  Information on preventing damage to electronic components due to electrostatic discharge   AH54.00-P-0001-01A
REMOVINGINSTALLING Remove/install     
1 Switch on ignition, select "Open camera cover" item in "Reversing camera" or "360° camera" menu and confirm. IMPORTANT The cover (1) opens.
INSTALLATION IMPORTANT : The cover (1) closes when the ignition is switched off or if the vehicle is driven forward.
 
2 Release both catches (arrows B) on swivel drive (9) and pull off cover (1).    
3 Switch off ignition and store transmitter key outside of transmission range (min. 2 m). INSTALLATION IMPORTANT : In the "Reversing camera" or "360° camera" menu, select the item "Open camera cover" and confirm.  
4 Remove trim from trunk lid. Model 205.3
with code 218 (Rear view camera)
Model 205.3
with code 501 (360° camera)
AR68.30-P-8151CLW
    Model 205.4
with code 218 (Rear view camera)
Model 205.4
with code 501 (360° camera)
AR68.30-P-8151LWR
5 Remove trunk lock. Model 205.3
with code 218 (Rear view camera)
Model 205.3
with code 501 (360° camera)
AR88.50-P-0003LW
6 Unscrew bolts (2).    
7 Push back catch hook (arrow A), remove swivel drive (9) and disconnect electrical connectors (4, 5). NOTES
When removing and inserting swivel drive (9), do not apply any lateral force to guide bars (8). Otherwise the guide bars (8) can break.
INSTALLATION IMPORTANT : Check drainage fitting (arrow C) is correctly seated in feed-through grommet (3).
IMPORTANT Do not pull electrical wiring harness (6) out further.
The marking (arrow D) must be in the outer guide (7).
 
8 Open cap (10) on swivel drive (9).    
9 Open clamp (11) and remove reversing camera (B84/3) or camera for rear 360° camera (B84/10).    
10 Install in the reverse order.    
11 Commission reversing camera (B84/3) using vehicle diagnosis system. Model 205.3/4
with code 218 (Rear view camera)
except code 235 (Active Parking Assist) When replacing reversing camera (B84/3).
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04B
12.1 Calibrate rear 360° camera (B84/10) or reversing camera (B84/3) using diagnostic system. Model 205.3/4
with code 218 (Rear view camera)
with code 235 (Active Parking Assist)
Model 205.3/4
with code 501 (360° camera)
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04B
12.2 Calibrate reversing camera (B84/3) with vehicle diagnosis system. Model 205.3/4
with code 218 (Rear view camera)
except code 235 (Active Parking Assist)
 
REFER TO SELF-DIAGNOSTIC SYSTEMS     AD00.00-P-2000-04B
    SPECIAL TOOL Calibration device Fig 2
Fig 2: Identifying Calibration Device (000 589 01 21 00)
G11128996Courtesy of MERCEDES-BENZ USA