Remove/Install Stabilizer Bar At Front Axle - AR32.35-P-2200LWX

Model 205, 213

with code M005 (4MATIC)

Model 253

MODIFICATION NOTES

15.09.2017

Basic data changed.

Step 5

Fig 1: Stabilizer Bar At Front Axle Components Location - Model 205, 213 With Code M005

Courtesy of MERCEDES-BENZ USA

Shown on model 205.0

Courtesy of MERCEDES-BENZ USA

Model 205.4

	Notes on self-locking nuts and bolts		AH00.00-N-0001-01A
	Notes on repair work on suspension components		AH00.00-P-0100-01A
	Remove/install
1.1	Remove center and rear engine compartment Model 205.0/1/2/3, 213 paneling with code M005 (4MATIC) Model 253 Model 205.0/1/2/3 with code M005 (4MATIC)		AR61.20-P-1105LW
	Model 253 Model 213 with code M005 (4MATIC)		AR61.20-P-1105LWE
1.2	Remove engine compartment paneling at center, rear and front	Model 205.4 with code M005 (4MATIC)	AR61.20-P-1105LW
2	Remove diagonal strut (8)	Model 205.4 with code M005 (4MATIC) Bolt, front diagonal strut to front axle carrier/torsion bar bearing shell/radiator mounting console	*BA61.10-P-1006-01L
3	Detach cover behind left and right diagonal struts (3)
4	Loosen bolts (4)	Model 205, 213 with code M005 (4MATIC) Bolt, torsion bar to front axle carrier	*BA32.20-P-1004-02R
		Model 253Bolt, torsion bar to front axle carrier	*BA32.20-P-1001-02T
5	Remove bolts (2) and remove left and right diagonal strut (3)	H Bolt, front diagonal strut to front axle carrier/torsion bar bearing shell/radiator mounting console	*BA61.10-P-1006-01L
		Bolt, front diagonal strut to longitudinal member	*BA61.10-P-1007-01L
6	Detach stabilizer bar link rod (5) at left and right from stabilizer bar (1)	Model 205, 213 with code M005 (4MATIC) Torsion bar linkage to torsion bar	*BA32.20-P-1005-02R
		Model 253 Torsion bar linkage to torsion bar	*BA32.20-P-1002-02T
7	Remove right suspension strut from spring link	Model 205, 213 with code 489 (AIRMATIC) with code M005 (4MATIC) Model 253 with code 489 (AIR BODY CONTROL)	AR32.25-P-1017LWL
8	Unscrew screws/bolts (4) and lower stabilizer bar (1)	Fit bolts (4) but do not tighten.
9	Remove stabilizer bar (1) toward rear	Model 205, 213 with code 489 (AIRMATIC) with code M005 (4MATIC) Model 253 with code 489 (AIR BODY CONTROL) Push right suspension strut outwards to the side.
10	Install in the reverse order

FRONT AXLE TORSION BAR

Number	Designation		Model 253
BA32.20-P-1001-02T	Bolt, torsion bar to front axle carrier	Nm	120

FRONT AXLE TORSION BAR

Number	Designation		Model 253
BA32.20-P-1002-02T	Torsion bar linkage to torsion bar	Nm	100

FRONT AXLE TORSION BAR

Number	Designation		Model 205 with code M005 (4MATIC)	Model 213 with code M005 (4MATIC)
BA32.20-P-1004-02R	Bolt, torsion bar to front axle carrier	Nm	120	120

FRONT AXLE TORSION BAR

Number	Designation		Model 205 with code M005 (4MATIC)	Model 213 with code M005 (4MATIC)
BA32.20-P-1005-02R	Torsion bar linkage to torsion bar	Nm	100	100

FRAME FLOOR ASSEMBLY

Number	Designation		Model 205	Model 213
BA61.10-P-1006-01L	Bolt, front diagonal strut to front axle carrier/torsion bar bearing shell/radiator mounting console	Nm	50	50

FRAME FLOOR ASSEMBLY

Number	Designation		Model 253
BA61.10-P-1006-01L	Bolt, front diagonal strut to front axle carrier/torsion bar bearing shell/radiator mounting console	Nm	50

FRAME FLOOR ASSEMBLY

Number	Designation		Model 205	Model 213
BA61.10-P-1007-01L	Bolt, front diagonal strut to longitudinal member	Nm	50	50

FRAME FLOOR ASSEMBLY

Number	Designation		Model 253
BA61.10-P-1007-01L	Bolt, front diagonal strut to longitudinal member	Nm	50