Adjust Trunk Lid - AR88.50-P-5200LW

Model 205.0/1/3

Model 213.0/1

Model 238.3

Courtesy of MERCEDES-BENZ USA

Shown on model 205.0 with code 218 (Reversing camera)

	Risk of injury caused by fingers being jammed or pinched when removing, installing or aligning hoods, doors, trunk lid/rear-end door or sliding roof.	No parts of the body or limbs should be within the operating area when the components are moving.	AS00.00-Z-0011-01A
	Notes on HANDS-FREE ACCESS		AH80.61-P-0001-01A
	Remove
1	Remove rear center assembly paneling		AR68.30-P-4785LW
2	Remove trim (1)	Model 205.0/1	AR68.30-P-8151LW
		Model 205.3	AR68.30-P-8151CLW
		Model 213.0/1, 238.3	AR68.30-P-8151LWE
	Adjust
3	Loosen bolts (3) for striker eye (4)
4	Expose left electrical wiring harness (6) in area of bolts (8) on left hinge lever	Model 205.0/1, 213.0/1 with code 218 (Rear view camera) Model 205.0/1, 213.0/1 with code 501 (360° camera) Model 205.3, 238.3
5	Expose right electrical wiring harness (7) in area of bolts (8) on right hinge lever
6	Loosen bolts (8) on left and right hinge lever
7	Adjust trunk lid (5) in longitudinal and transverse direction	Model 205.0/1/3 Trunk lid to fender at rear, top	*BE60.00-P-1012-01BB
		Model 205.0/1/3 Trunk lid to bumper	*BE60.00-P-1014-01BB
		Model 213.0/1 Trunk lid to fender at rear, top	BE60.00-P-1011-01GA
		Model 213.0/1 Trunk lid to bumper	BE60.00-P-1013-01GA
		Model 238.3 Trunk lid to fender at rear, top	BE60.00-P-1009-01HA
		Model 238.3 Trunk lid to bumper	BE60.00-P-1011-01HA
		Feeler gauge	Fig 1
8	Tighten bolts (8) on left and right hinge lever	Bolt, hinge bracket to trunk lid	*BA88.50-P-1001-03A
9	Repair paint damage in area of hinge lever with primer filler and touch-up paint pen	Use only primer filler and paints approved by Daimler AG
10	Protect area around hinge lever against corrosion	Cavity preservation (free of solvents), 1 liter	*BR00.45-Z-1003-05A
11	Fasten right electrical wiring harness (7)
12	Fasten left electrical wiring harness (6)	Model 205.0/1, 213.0/1 with code 218 (Rear view camera) Model 205.0/1, 213.0/1 with code 501 (360° camera) Model 205.3, 238.3
13	Completely screw in stop buffers (2)
14	Adjust height of trunk lid (5) by moving lock striker (4)	The top edge of the trunk lid (5) must be flush with the fenders.
15	Center lock striker (4) in relation to trunk lid lock and tighten bolts (3)
	Install
16	Install cover (1)	Model 205.0/1	AR68.30-P-8151LW
		Model 205.3	AR68.30-P-8151CLW
		Model 213.0/1, 238.3	AR68.30-P-8151LWE
17	Install rear center section paneling		AR68.30-P-4785LW
	Adjust
18	Mark stop buffers (2) in contact area with chalk
19	Unscrew stop buffers (2) in small increments until trunk lid (5) makes contact with stop buffers (2) when closed and an imprint of the chalk is visible on the engine hood
20	Unscrew stop buffers (2) by a quarter turn	The trunk lid (5) is distorted slightly to prevent vibrations.
	Calibrate
21	Calibrate 360° rear camera with diagnostic system added
		Model 205.0/1/3 with code 501 (360° camera) Model 213.0/1 with code 501 (360° camera)	AD00.00-P-2000-04B
		Model 238.3 with code 501 (360° camera)	AD00.00-P-2000-06LWO