Check condition of battery - AR54.10-P-1129NKB

MODEL 117, 156, 176, 242, 246 

Fig 1: Identifying Battery Components

Courtesy of MERCEDES-BENZ USA

	Risk of injury  due to fan starting unexpectedly	Do not reach into the rotation or hazard area of the fan. Wear closed and close-fitting work clothes.	AS20.40-Z-0001-01A
	Risk of explosion  from explosive gas. Risk of poisoning and caustic burns  from swallowing battery electrolyte. Risk of injury  through burns to skin and eyes from battery acid or when handling damaged lead-acid batteries	No fires, sparks, open flames or smoking. Wear acid-resistant gloves, clothing and glasses. Only pour battery acid into suitable and appropriately marked containers.	AS54.10-Z-0001-01A
	Notes on battery		AH54.10-P-0001-01A
	Remove
1	Open engine hood
2	Unclip retaining clip (2.1) for engine wiring harness (2) from cover (1)	Model 117, 156, 176, 246 with engine 607, 651
3	Unclip engine hood cable (3) from cover (1)	Model 117, 156, 176, 246 Model 242 except code ME01 (Electric motor)
4	Unlock cover (1) in direction of arrow and remove	Model 117, 156, 176, 246 Model 242 except code ME01 (Electric motor)
5	Disconnect ground line for on-board electrical system battery (G1)	Model 242 with code ME01 (Electric motor)
			AR54.10-P-0003NKB
	Check
6	Visually inspect on-board electrical system battery (G1) for external leakage	If leaks are found, replace the on-board electrical system battery (G1). ↓
		Remove/install battery	AR54.10-P-0005NKB
7	Check on-board electrical system battery (G1)		AR54.10-P-1129-01A
	000 588 02 19 00 Battery tester		WS54.00-N-3006B
		Battery capacity 60 Ah	*BE54.10-P-1007-01A
		Battery capacity 70 Ah VRLA	*BE54.10-P-1010-01A
		Battery capacity 80 Ah VRLA	*BE54.10-P-1012-01A
8	Reduce increased voltage after charging process For an on-board electrical system battery (G1) that is disconnected from the on-board electrical system and if the message "Surface voltage detected" is in the display of the Midtronics battery tester.
			AR54.10-P-1129-03A
	000 588 03 19 00 Load tester		WS15.00-P-0027B
		Check the on-board electrical system battery (G1) again after the increased voltage is reduced.
9	Charge on-board electrical system battery (G1)	With the test code "Charge and check" on the Midtronics battery tester.
			AR54.10-P-1130NKB
		Check the on-board electrical system battery (G1) again after charging.
	Install
10	Connect ground line for on-board electrical system battery (G1)	Model 242 with code ME01 (Electric motor)
			AR54.10-P-0003NKB
11	Install cover (1)	Model 117, 156, 176, 246 Model 242 except code ME01 (Electric motor)
12	Clip engine hood cable (3) into cover (1)	Model 117, 156, 176, 246 Model 242 except code ME01 (Electric motor)
13	Clip retaining clip (2.1) for engine wiring harness (2) into cover (1)	Model 117, 156, 176, 246 with engine 607, 651
14	Close engine hood

TEST AND ADJUSTMENT VALUES FOR BATTERY

Number	Designation				Model all
BE54.10-P-1007-01A	Battery capacity 60 Ah	Cold cranking amps	As per EN	A	510

TEST AND ADJUSTMENT VALUES FOR BATTERY

Number	Designation				Model all
BE54.10-P-1010-01A	Battery capacity 70 Ah VRLA	Cold cranking amps	As per EN	A	760

TEST AND ADJUSTMENT VALUES FOR BATTERY

Number	Designation				Model all
BE54.10-P-1012-01A	Battery capacity 80 Ah VRLA	Cold cranking amps	As per EN	A	800