LEMON Manuals: Even more car manuals for everyone
Home >> Mercedes Benz >> 2016 >> Metris Van Cargo >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Illumination Lights >> Electrical System -- Body (3 Of 6) -- 447 Chassis >> Retrofitting & Conversion >> Retrofit CNS For Satellite Radio Mode With SDARS Antenna On Rear Roof Paneling >> Retrofit CNS For Satellite Radio Mode With SDARS Antenna On Rear Roof Paneling - AZ82.85-S-0014E

Retrofit CNS For Satellite Radio Mode With SDARS Antenna On Rear Roof Paneling - AZ82.85-S-0014E

Model 447.6 

with code EN6 (Audio 10) 

with code ZU7 (National version for Canada) 

except code ER0 (Radio, pre-wiring) 

except code ME0 (Electric motor 85 kW) 

Model 447.6 

with code EN6 (Audio 10) 

with code ZU8 (National version for USA) 

except code ER0 (Radio, pre-wiring) 

except code ME0 (Electric motor 85 kW) 

Model 447.6 

with code EN7 (Audio 15) 

with code ZU7 (National version for Canada) 

except code ER0 (Radio, pre-wiring) 

except code ME0 (Electric motor 85 kW) 

Model 447.6 

with code EN7 (Audio 15) 

with code ZU8 (National version for USA) 

except code ER0 (Radio, pre-wiring) 

except code ME0 (Electric motor 85 kW) 

G16489088Courtesy of MERCEDES-BENZ USA

Communication and navigation system (CNS) 

Shown on model 447.7 with code EN7 (Audio 15) 

G16489089Courtesy of MERCEDES-BENZ USA
G16489090Courtesy of MERCEDES-BENZ USA

Shown on model 447.7 with code LC4 (Comfort overhead control panel) 

Shown on model 447.7 except code LC4 (Comfort overhead control panel) and except code LD0 (Overhead control panel with two reading lights) 

G16489091Courtesy of MERCEDES-BENZ USA

Satellite radio equipment 

G16489092Courtesy of MERCEDES-BENZ USA
Notice  Information on preventing damage to electronic components due to electrostatic discharge   AH54.00-P-0001-01A
Notice  Notes on carrying out repair work in the vehicle interior   AH68.00-D-0001-01KOS
REMOVING Remove     
1 Read out security code of radio (Audio) (N87/2) via Vehicle Documentation (VeDoc) and enter on the form.    
REFER TO FORMS Provide radio code to customer, form IMPORTANT Hand over form to customer. OF82.60-Z-3000-04KCV
2 Detach ground line of on-board electrical system battery.    
REFER TO TESTING & REPAIR     AR54.10-S-0003E
3 Remove center instrument panel cover.    
REFER TO TESTING & REPAIR   Model 447.6/7 except code XM7 (Facelift II) AR68.10-S-3430E
4 Remove USB/AUX connection (A40/10) from center instrument panel cover. IMPORTANT Tie back plug (7) with electric lines of the universal serial bus/AUX connection (A40/10) and fix in place with cable ties at factory-installed electrical wiring harness.  
5 Remove radio (Audio) (N87/2) and standard radio installation frame.    
REFER TO TESTING & REPAIR   Model 447.6/7 except code XM7 (Facelift II) AR82.60-S-7502E
    IMPORTANT Hand over removed radio (Audio) (N87/2) with standard radio installation frame to customer.  
    IMPORTANT The screws (8) of the removed radio (Audio) (N87/2) are used for fastening the CNS head unit (1).  
6 Remove GPS antenna (A2/47).    
REFER TO TESTING & REPAIR   Model 447.6 with code E1N (Becker® MAP PILOT) Model 447.6 with code EV6 (Becker® MAP PILOT pre-installation) AR82.85-S-0002E
7 Detach center instrument panel speaker (H4/27).    
REFER TO TESTING & REPAIR   IMPORTANT Do not disconnect electrical wiring plugs. AR82.62-S-7833E
8 Remove right A-pillar trim.    
REFER TO TESTING & REPAIR     AR68.30-S-4050E
9.1 Remove front overhead control panel (OCP) control unit (N70). Model 447.6 with code LC4 (Comfort overhead control panel) model 447.6 with code LD0 (Overhead control panel with two reading spots)  
REFER TO TESTING & REPAIR     AR82.20-S-1100E
9.2 Remove front dome lamp (10). Model 447.6 except code LC4 (Comfort overhead control panel) except code LD0 (Overhead control panel with two reading lights)  
REFER TO TESTING & REPAIR     AR82.20-S-0110E
10.1 Remove hands-free system microphone (B25/4) from front overhead control panel (OCP) control unit (N70). Model 447.6 with code LC4 (Comfort overhead control panel) model 447.6 with code LD0 (Overhead control panel with two reading spots)  
    IMPORTANT For this, release catch (arrow) at overhead control panel (OCP) control unit (N70) and remove hands-free system microphone (B25/4).  
10.2 Remove hands-free system microphone (B25/4) from front dome lamp (10). Model 447.6 except code LC4 (Comfort overhead control panel) except code LD0 (Overhead control panel with two reading lights)  
    IMPORTANT To do so, release catch (arrow) at front dome lamp (10) and remove hands-free system microphone (B25/4).  
11 Remove right sun visor.    
REFER TO TESTING & REPAIR     AR68.60-S-5480E
12 Remove right grab handle on front roof lining.    
REFER TO TESTING & REPAIR     AR68.30-S-4330E
13 Remove right top B-pillar trim.    
REFER TO TESTING & REPAIR     AR68.30-S-4700E
14 Slightly detach front roof lining from right roof frame at side.    
REFER TO TESTING & REPAIR     AR68.30-S-7607E
    NOTES Carefully detach front roof lining.
Otherwise, the front roof lining may be damaged.		  
    IMPORTANT Do not remove front roof lining.
Do not disconnect electrical wiring plugs.		  
15 Remove roof lining from load compartment.    
REFER TO TESTING & REPAIR   Model 447.6 with code VD2 (Standard headliner, B-D pillar) AR68.30-S-7618E
16 Remove additional brake lamp.    
REFER TO TESTING & REPAIR   Model 447.6 with code W50 (Double-wing rear-end door, 180 degrees without window) Model 447.6 with code W54 (Double-wing rear-end door, 270 degrees) AR82.10-S-5375EE
    IMPORTANT Do not disconnect electrical connector.  
  Preparation     
17 Prepare CNS head unit (1) for installation. IMPORTANT For this purpose, use the CNS head unit (1), cover (2) and supplied screws. AZ82.85-S-0008-01E 
18 Perform aftermarket modification to antenna line to TMC antenna splitter (A28/13) for CNS head unit (1). Model 447.6 with code E1N (Becker® MAP PILOT) Model 447.6 with code EV6 (Becker® MAP PILOT pre-installation) AZ82.85-S-0008-08E 
    SPECIAL TOOL Wiring harness repair kit, basic Fig 1
INSTALLING Install     
19 Retrofit antenna (14). Model 447.6 with code W50 (Double-wing rear-end door, 180 degrees without window) Model 447.6 with code W54 (Double-wing rear-end door, 270 degrees) AZ82.85-S-0014-01E 
    Model 447.6 with code W65 (Tailgate) AZ82.85-S-0014-01EA 
20 Retrofit SDAR tuner (13).   AZ82.85-S-0014-02E 
21 Retrofit hands-free system microphone (4).   AZ82.70-S-0005-08E 
22 Retrofit GPS antenna (3).   AZ82.85-S-0012-04E 
23 Retrofit connecting cables for CNS head unit (1). IMPORTANT The connecting cables for the CNS head unit (1) consist of the USB connection cables (5) and USB cover (9) as supplied. AZ82.85-S-0008-03E 
24 Retrofit CAN cable with adapter (6) for CNS head unit (1). IMPORTANT Install the CAN cable with adapter (6) with supplied antenna adapter. AZ82.85-S-0008-05E 
    SPECIAL TOOL Wiring harness repair kit, basic Fig 1
25 Retrofit CNS head unit (1).   AZ82.85-S-0008-02E 
26 Attach ground line of on-board electrical system battery.    
REFER TO TESTING & REPAIR     AR54.10-S-0003E
27 Make basic settings on CNS head unit (1). NOTES To do so, operate parking brake.
This enables the setting to be made on the CNS head unit (1) in the control menu.		  
    IMPORTANT See Owner's Manual.  
28 Install additional brake lamp.    
REFER TO TESTING & REPAIR   Model 447.6 with code W50 (Double-wing rear-end door, 180 degrees without window) Model 447.6 with code W54 (Double-wing rear-end door, 270 degrees) AR82.10-S-5375EE
    IMPORTANT Do not disconnect electrical connector.  
29 Install roof lining in load compartment.    
REFER TO TESTING & REPAIR   Model 447.6 with code VD2 (Standard headliner, B-D pillar) AR68.30-S-7618E
30 Fasten front roof lining to right roof frame at side.    
REFER TO TESTING & REPAIR   NOTES Carefully fasten front roof lining.
Otherwise, the front roof lining may be damaged.		 AR68.30-S-7607E
31 Install right top B-pillar trim.    
REFER TO TESTING & REPAIR     AR68.30-S-4700E
32 Install right grab handle on front roof lining.    
REFER TO TESTING & REPAIR     AR68.30-S-4330E
33 Install right sun visor.    
REFER TO TESTING & REPAIR     AR68.60-S-5480E
34 Install center instrument panel cover.    
REFER TO TESTING & REPAIR   Model 447.6/7 except code XM7 (Facelift II) AR68.10-S-3430E
    IMPORTANT Make sure that the USB cover (9) with USB ports is correctly engaged in installation opening of center instrument panel cover.  
35.1 Install front overhead control panel (OCP) control unit (N70). Model 447.6 with code LC4 (Comfort overhead control panel) model 447.6 with code LD0 (Overhead control panel with two reading spots)  
REFER TO TESTING & REPAIR     AR82.20-S-1100E
35.2 Install front dome lamp (10). Model 447.6 except code LC4 (Comfort overhead control panel) except code LD0 (Overhead control panel with two reading lights)  
REFER TO TESTING & REPAIR     AR82.20-S-0110E
36 Attach center instrument panel speaker.    
REFER TO TESTING & REPAIR     AR82.62-S-7833E
37 Install right A-pillar trim.    
REFER TO TESTING & REPAIR     AR68.30-S-4050E
38 Document retrofitted equipment in VeDoc. IMPORTANT Attach "Communication and Navigation System (CNS) for satellite radio mode retrofitted as per AZ82.85-S-0014E" note under field organization texts to design group 82.  
    IMPORTANT Remove existing code EN6 (Audio 10) or code EN7 (Audio 15).  
    IMPORTANT Model 447.6 with code EN7 (Audio 15) with code EV6 (Pre-installation for Becker® MAP PILOT)
Remove existing code EV6 (Becker® MAP PILOT pre-installation).		  
    IMPORTANT Model 447.6 with code EN7 (Audio 15) with code E1N (Becker® MAP PILOT)
Remove existing code E1N (Becker® MAP PILOT).		  
39 Connect vehicle diagnosis system, read out fault memory    
REFER TO SELF-DIAGNOSTIC SYSTEMS Connect STAR DIAGNOSIS and read out fault memory   AD00.00-S-2000-04E
40 Perform SCN coding on electronic ignition lock (EZS) control unit (N73).    
REFER TO TESTING & REPAIR   IMPORTANT Under the "Control unit adaptations" menu item follow the instructions for "SCN coding". AR54.21-S-0015E
41 Perform SCN coding on instrument cluster (IC) control unit (A1/1).    
REFER TO TESTING & REPAIR   IMPORTANT Under the "Control unit adaptations" menu item follow the instructions for "SCN coding". AR54.21-S-0015E
42 Remove diagnostic system.    
INSPECT Check     
43 Perform function test. IMPORTANT See Owner's Manual.
The satellite radio mode must be activated by the customer. For this, hand the instructions supplied by the satellite radio provider to the customer.		  
Fig 1: Identifying Wiring Harness Repair Kit, Basic (000 589 13 99 00)
G07304826Courtesy of MERCEDES-BENZ USA
PARTS ORDERING NOTE

Part no. Designation Quantity
  Parts kit (see "ODUS"), Communication and Navigation System (CNS) with satellite radio equipment 1
scientia non olet · About LEMON Manuals